O.S. engine MAX FXi 46 Page 8 Owner'S Instruction Manual Download | Manualshive

Page: 8 / 28

background image

Installation in the Model

Make sure that the mounting beams are
parallel and that their top surfaces are in the
same plane.

•

Before connecting the throttle-
lever/servo linkage, make sure that no
part of the linkage interferes with the
internal structure of the aircraft or
wiring, etc., when the throttle is fully
open or fully closed.

•

Set the throttle lever linkage so that the
throttle rotor is (a) fully open when the
transmitter throttle stick is fully
advanced and (b) fully closed when the

THROTTLE LINKAGE

INSTALLATION OF THE ENGINE

BASIC ENGINE PARTS

8

«
...
6
7
8
9
10
...
»

Summary of Contents for MAX FXi 46





























Reviews:

No comments

Related manuals for MAX FXi 46

Brand: Yanmar Pages: 224

Brand: hager Pages: 4

Brand: WÄRTSILÄ Pages: 200

Brand: MSW Pages: 159

Brand: DELTA DORE Pages: 16

Brand: Briggs & Stratton Pages: 6

Brand: MTU Pages: 187

Brand: Siemens Pages: 20

Brand: Siemens Pages: 26

Brand: Siemens Pages: 40

Brand: Siemens Pages: 87

Brand: Siemens Pages: 96

Brand: Siemens Pages: 116

Brand: Siemens Pages: 156

Brand: Siemens Pages: 252

24 v High Performance Synchronous Motor

Brand: Rega Pages: 1

Brand: AL-KO Pages: 132

Brand: RADEMACHER Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands