background image

NOTES!

This engine was designed for model
aircraft. Do not attempt to use it for any
other purpose.

Mount the engine in your model
securely,  following the manufacturers’
recommendations,  using appropriate
screws and locknuts.

Be sure to use the muffler supplied with
the engine. Frequent exposure to an
open exhaust may eventually impair

Never operate your engine in an
enclosed space. Model engines, like
automobile engines, exhaust deadly
carbon monoxide. Run your engine only
in an open area.

Model engines generate considerable
heat. Do not touch any part of your
engine until it has cooled. Contact with the
muffler  (silencer), cylinder head or
exhaust header pipe, in particular, may
result in a serious burn.

WARNINGS!

Never touch, or allow any object to
come into contact with, the rotating
propeller and do not crouch over the
engine when it is running.

A weakened or loose propeller may
disintegrate or be thrown off and, since
propeller tip speeds with powerful
engines may exceed 600 feet (180 meters)
per  second, it will be understood that
such a failure could result in serious
injury, (see “NOTES!” section relating to
propeller safety).

Model engine fuel is poisonous. Do not
allow it to come into contact with the
eyes or mouth. Always store it in a
clearly marked container and out of the
reach of children.

Model engine fuel is also highly
flammable. Keep it away from open
flame, excessive heat, sources of
sparks, or anything else which might
ignite it. Do not smoke or allow anyone
else to smoke, near fuel.

4

Summary of Contents for MAX FXi 46





























Reviews: