background image

16

INSTLLATION OF PROPELLER

Install  the  propeller  on  the  shaft  so  that  the 
curved  face  of  the  blades  faces  forward  –  i.e.  in 
the direction of flight. Firmly tighten the propeller 
washer  and  propeller  retaining  screws  using  the 
correct  size  wrench.  Always  check  the  tightness 
of  propeller  retaining  screws  and  retighten  them, 
if necessary, before restarting the engine. 

If  the  supplied  retaining  screws  are  too  long  due  to  a 
thinner  prop  hub  or  too  short  due  to  a  thicker  prop  hub 
(cannot  be  screwed  into  the  drive  hub  by  more  than 
10mm), Use suitable length strong steel hex socket head 
cap screws.

Install  the  propeller  before  the  first  flight  of  the  day  and 
remove it after the day’s flight.

Make a habit of always checking the tightness of propeller 
retaining screws making sure they are free of, damage or 
rust  before  starting  the  engine.    Replace  the  propeller 
periodically (every 50 flights) even if it looks as ifs nothing 
is wrong.

17

Use  regular  gasoline.  (No  need  to  use  high  octane 
gasoline.)

Alcohol  based  glow  fuel  cannot  be  used  in  this  engine.   
Not only will the engine not work properly but the internal 
carburetor plastic parts will be damaged.

Use  high  quality  commercially  available  2  stroke  engine 
oil.

Follow  the  oil  manufacturer’s  recommendations 
concerning the mixture ratio of gasoline and oil.  If there is 
no recommendation, mix with a 30:1 ratio.
We  have  checked  and  approved  the  following  oil  mixture 
ratio.
KLOTZ ModelLube  (50:1), COSMO Cosmo Terra 2 cycle 
(50:1), RED LINE Two-Stroke Racing Oil (40:1). 
(This  does  not  mean  we  guarantee  the  quality  of  these 
oils.)
Follow the instructions in the running-in section concerning 
the mixture for running-in.

With  a  gasoline  engine,  passages  in  the  carburetor  are 
narrower  than  that  of  a  glow  engine,  and  therefore  very 
sensitive  against  foreign  matter  such  as  dust.  It  is 
suggested to use optional accessory Super Filter L (Code 
No.  72403050)  when  filling  a  tank  in  the  model  from  a 
container used for transportation or storing.

Gasoline  is  poisonous.  Do  not  allow  it  to  come 
into contact with the eyes or mouth. Always store 
it in a clearly marked container in a cool and dark 
place  out  of  the  reach  of  children.  There  is  a 
possibility that it may damage your health.

Gasoline is highly flammable.  Keep it away from 
an  open  flame,  excessive  heat,  sources  of 
sparks, or anything else which might ignite it. 
Do  not  smoke  or  allow  anyone  else  to  smoke 
near to it.

Carry  out  mixing  of  gasoline  and  oil  in  a  well-
ventilated and free of fire outdoor, place or there 
is a possibility of fire.

Refill  the  models  fuel  tank  only  after  the  engine 
has well cooled down, or there is a danger of fire.

Observe the laws and regulations in each country 
and district concerning the usage, transportation 
and storage of gasoline. Ask details at fire station 
in each district.

MIXING OF OIL

R

Summary of Contents for GT55



















Reviews: