background image

10

Tools,  accessories,  etc.  The  following  items 
are necessary for operating the engine.

BEFORE STARTING

The choice of propeller depends on the design 
and weight of the aircraft and the type of flying 
in which you will be engaged.
Determine  the  best  size  and  type  after 
practical  experimentation.  As  a  starting  point, 
refer  to  the  props  listed  in  the  accompanying 
table. Slightly larger, or even slightly smaller,  

Propellers

Type

props  than  those  shown  in  the  table  may  be 
used,  but  remember  that  the  propeller  noise 
will  increase,  due  to  higher  rpm  or  if  a  larger-
diameter/lower-pitched prop is used.

Never touch, or allow any object to come into 

contact with, the rotating propeller and do not 

crouch over the engine when it is running.

Reminder!

Warning:
Make  sure  that  the  propeller  is  well 
balanced.  An  unbalanced  propeller  and/or 
spinner  can  cause  serious  vibration  which 
may weaken parts of the airframe or affect 
the safety of the radio-controlled system.
DO NOT forget the WARNINGS and NOTES 
on  propeller  and  spinner  safety  given  on 
front pages.

Scale

Sport & Aerobatic

Size(DxP)

13x7-9, 14x6-8
15x6-8

11

Since  the  FS-95V  is  intended  to 
be started with an electric starter, 
the  addition  of  a  spinner 
assembly  for  centering  the  starter  sleeve  is 
desirable.  Use  a  heavy-duty,  well  balanced 
spinner either of metal or plastic.

Spinner

FUEL

The FS-95V should be operated on a methanol based 
fuel containing not less than 18% (volumetric) castor oil, 
or a top quality synthetic lubricant (or a mixture of both), 
plus a small percentage (5-20%) of nitromethane for 
improved  flexibility  and  power.  (The  carburetor  is 
adjusted a little on the rich side at the factory for a fuel 
containing 20% lubricant and 15% nitromethane.) Some 
commercial fuels also contain coloring additives as an 
aid to fuel level visibility.  In some cases, these additives 
have  indicated  slightly  negative  effects  on  the 
performance.

Model  engine  fuel  is  poisonous.  Do  not 
allow it to come into contact with the eyes or 
mouth.  Always  store  it  in  a  clearly  marked 
container and out of the reach of children.
Model  engine  fuel  is  also  highly  flammable. 
Keep  it  away  from  open  flame,  excessive 
heat,  sources  of  sparks,  or  anything  else 
which might ignite it. Do not smoke, or allow 
anyone else to smoke, near to it.

Reminder!

We would suggest that you use such fuels only if you 
are satisfied that they do not adversely affect running 
qualities when compared with familiar standard fuels. 
When  changing  to  a  fuel  brand  or  formula  that  is 
different from the one to which you are accustomed, it is 
a  wise  precaution  to  temporarily  revert  to  in-flight 
running-in  procedures,  until  you  are  sure  that  the 
engine is running entirely satisfactorily.

Summary of Contents for FS-95V






















Reviews: