background image

It is of vital importance, before attempting to operate 
your  engine,  to  read  the  general 

'SAFETY 

INSTRUCTIONS AND WARNINGS' section on pages 
2-6 of this booklet and to strictly adhere to the advice 
contained therein.

● 

Also,  please  study  the  entire  contents  of  this 
instruction  manual,  so  as  to  familiarize  yourself 
with the controls and other features of the engine.

Keep these instructions in a safe place so that you 
may readily refer to them whenever necessary.

It  is  suggested  that  any  instructions  supplied  with 
the  aircraft,  radio  control  equipment,  etc.,  are 
accessible for checking at the same time.

● 

● 

1

2-6

7

8

9

10-13

20

21

27-28

34-35

36-37

38

17-18

SAFETY INSTRUCTIONS AND WARNINGS 
ABOUT YOUR O.S. ENGINE

NOTES WHEN APPLYING AN ELECTTRIC STARTER

ABOUT THE ENGINE

ENGINE PARTS NAME

BEFORE STARTING

INSTALLATION

INSTALLING SILENCER 

FUEL TANK & LINES

PROPELLER

GLOWPLUG

CONTENTS

MIXTURE CONTROLS

STARTING

RUNNING -IN ("Breaking-in")

IDLE MIXTURE ADJUSTMENT

CARE AND MAINTENANCE

ENGINE EXPLODED VIEW & PARTS LIST

CARBURETOR EXPLODED VIEWS
& PARTS LIST

GENUINE PARTS & ACCESSORIES

THREE VIEW DRAWING

MEMO

29-30

31-33

39

40

14-16

19

22-23

24-26

Summary of Contents for FS-95V






















Reviews: