manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Reference Manual

The NXP Semiconductors MC9S08PA4 is a powerful microcontroller offering exceptional performance and versatility. To maximize your understanding and effectively utilize its features, we provide a comprehensive Reference Manual available for free download at manualshive.com, offering detailed instructions and guidelines for optimal usage.

Share
Download
background image

SCIx_C3 field descriptions

Field

Description

7

R8

Ninth Data Bit for Receiver

When the SCI is configured for 9-bit data (M = 1), R8 can be thought of as a ninth receive data bit to the
left of the msb of the buffered data in the SCI_D register. When reading 9-bit data, read R8 before reading
SCI_D because reading SCI_D completes automatic flag clearing sequences that could allow R8 and
SCI_D to be overwritten with new data.

6

T8

Ninth Data Bit for Transmitter

When the SCI is configured for 9-bit data (M = 1), T8 may be thought of as a ninth transmit data bit to the
left of the msb of the data in the SCI_D register. When writing 9-bit data, the entire 9-bit value is
transferred to the SCI shift register after SCI_D is written so T8 should be written, if it needs to change
from its previous value, before SCI_D is written. If T8 does not need to change in the new value, such as
when it is used to generate mark or space parity, it need not be written each time SCI_D is written.

5

TXDIR

TxD Pin Direction in Single-Wire Mode

When the SCI is configured for single-wire half-duplex operation (LOOPS = RSRC = 1), this bit determines
the direction of data at the TxD pin.

0

TxD pin is an input in single-wire mode.

1

TxD pin is an output in single-wire mode.

4

TXINV

Transmit Data Inversion

Setting this bit reverses the polarity of the transmitted data output.

NOTE: Setting TXINV inverts the TxD output for all cases: data bits, start and stop bits, break, and idle.

0

Transmit data not inverted.

1

Transmit data inverted.

3

ORIE

Overrun Interrupt Enable

This bit enables the overrun flag (OR) to generate hardware interrupt requests.

0

OR interrupts disabled; use polling.

1

Hardware interrupt requested when OR is set.

2

NEIE

Noise Error Interrupt Enable

This bit enables the noise flag (NF) to generate hardware interrupt requests.

0

NF interrupts disabled; use polling).

1

Hardware interrupt requested when NF is set.

1

FEIE

Framing Error Interrupt Enable

This bit enables the framing error flag (FE) to generate hardware interrupt requests.

0

FE interrupts disabled; use polling).

1

Hardware interrupt requested when FE is set.

0

PEIE

Parity Error Interrupt Enable

This bit enables the parity error flag (PF) to generate hardware interrupt requests.

0

PF interrupts disabled; use polling).

1

Hardware interrupt requested when PF is set.

Chapter 14 Serial communications interface (SCI)

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

NXP Semiconductors

281

Summary of Contents for MC9S08PA4


















































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S08PA4

Watlow F4T Installation And Troubleshooting User’S Manual preview
F4T
Brand: Watlow Pages: 59
Watts Tekmar WiFi Snow Melting Control 670 Installation Manual preview
Tekmar WiFi Snow Melting Control 670
Brand: Watts Pages: 48
KEB COMBIVERT F5 Safety Manual preview
COMBIVERT F5
Brand: KEB Pages: 16
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Brand: DAYLIFF Pages: 40
Italtecnica Brio 2000 Owner'S Manual preview
Brio 2000
Brand: Italtecnica Pages: 16
Danfoss VLT LCP 601 Installation Manual preview
VLT LCP 601
Brand: Danfoss Pages: 8
Danfoss AMD 613 Installation Manual preview
AMD 613
Brand: Danfoss Pages: 2
ZALMAN ZM-MFC3 User Manual preview
ZM-MFC3
Brand: ZALMAN Pages: 8
Linx Technologies HumPRO Series Quickstart Reference preview
HumPRO Series
Brand: Linx Technologies Pages: 2
Whadda L298N User Manual preview
L298N
Brand: Whadda Pages: 7
CSZ EZT-550 Instruction Manual preview
EZT-550
Brand: CSZ Pages: 69
MDT AKI-0416.01 Manual preview
AKI-0416.01
Brand: MDT Pages: 39
Barth Mini-PLC STG-660 CAN Manual preview
Mini-PLC STG-660 CAN
Brand: Barth Pages: 7
Naturela NPBC-V3C-K User Manual preview
NPBC-V3C-K
Brand: Naturela Pages: 31
OJ Electronics ETOP-4770 Manual preview
ETOP-4770
Brand: OJ Electronics Pages: 46
GDS Corp C2 Protector Quick Start Manual preview
C2 Protector
Brand: GDS Corp Pages: 2
Asus AAEON BOXER-6614 User Manual preview
AAEON BOXER-6614
Brand: Asus Pages: 112

Brands by name

Popular brands

Load more brands