NXP Semiconductors LPC55 Series User Manual Download Page 16 | Manualshive

Page: 16 / 24

NXP Semiconductors LPC55 Series User Manual Download Page 16

UM11158

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2019. All rights reserved.

User manual

Rev. 1.2 — 25 April 2019

16 of 24

NXP Semiconductors

UM11158

LPCXpresso55S69 Development Board

7.2 Micro SD card slot

The micro SD card (P21) included in the LPCXpresso55S69 board provides a 4-bit SDIO
interface to support memory cards, plug-in WiFi modules, etc. Power enable to the socket
is provided via transistor enabled by P1_0.

Software drivers and related examples for the SD card are provided as part of the
MCUXpresso SDK.

7.3 Accelerometer

The board includes an NXP MMA8652FCR1 accelerometer, interfaced to Flexcom 4
(ports P1_21 and P1_20) with its interrupt output connected to P1_19 (this signal is also
shared with the Expansion connector P18 via a 100 ohm resistor (R5).) The
accelerometer has an I2C address of 0b0011101.

Note that the accelerometer can only be used when the board is configured for 3.3V
operation. Resistor R20 may be removed to disconnect the MMA8652 from the supply
rail, and P25 may be installed to provide a convenient way to connect/disconnect it to/from
power.

Resistors R3 and R4 are zero ohm links, provided to enable the MMA8652 to be
disconnected from P1_20 and P1_21 to avoid leakage effects when the board is
configured for 1.8V operation.

I2C software drivers are provided as part of the MCUXpresso SDK, and example code is
provided to illustrate how to read values from the accelerometer.

7.4 RGB User LED

An User controlled RGB LED is provided on the Board, located on the right hand edge.
The LEDs in this device are controlled by LPC55S69 ports P1_4 (Blue), P1_6 (Red), P1_7
(Green) with the LEDs being illuminated when the respective LED is pulled low. Note that
these port lines are also connected to expansion connector J18.

7.5 Buttons

Four buttons are provided on the LPCXpresso55S69, as described in this section.

Table 3.

Micro SD card connections

SDIO interface signals

Port

Notes

SDIO Clock

P0_7

IOCON function 2

SDIO Command

P0_8

IOCON function 2

D0

P0_9

IOCON function 2

D1

P0_17

IOCON function 2

D2

P0_24

IOCON function 2

D3

P0_25

IOCON function 2

Card detect

P0_21

IOCON function 2

Power enable

P1_0

GPIO. Active low.

«
...
14
15
16
17
18
...
»

Summary of Contents for LPC55 Series

























Reviews:

No comments