manualshive.com logo in svg

NXP Semiconductors LPC1311, User Manual, Page: 27 / 368

Share
Download
NXP Semiconductors LPC1311 User Manual Download Page 27

UM10375

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 3 — 14 June 2011 

27 of 368

NXP Semiconductors

UM10375

Chapter 3: LPC13xx System configuration

3.5.19 SSP0 clock divider register

This register configures the SSP0 peripheral clock SSP0_PCLK. The SSP0_PCLK can be 
shut down by setting the DIV bits to 0x0.

 

3.5.20 UART clock divider register

This register configures the UART peripheral clock UART_PCLK. The UART_PCLK can 
be shut down by setting the DIV bits to 0x0.

Remark: 

 Note that for the LPC1311/13/42/43, the UART pins must be configured in the 

IOCON block before the UART clock can be enabled. For the LPC1311/01 and 
LPC1313/01 no special enabling sequence is required.

 

15

WDT

Enables clock for WDT.

0

0

Disabled

1

Enabled

16

IOCON

Enables clock for IO configuration block.

0

0

Disabled

1

Enabled

17

-

-

Reserved

0x00

18

SSP1

Enables clock for SSP1.

0

0

Disable

1

Enable

31:19

-

-

Reserved

0x00

Table 25.

System AHB clock control register (SYSAHBCLKCTRL, address 0x4004 8080) bit 
description 

 …continued

Bit

Symbol

Value

Description

Reset 
value

Table 26.

SSP0 clock divider register (SSP0CLKDIV, address 0x4004 8094) bit description

Bit

Symbol

Description

Reset value

7:0

DIV

SSP_PCLK clock divider values.
0: Disable SSP0_PCLK. 
1: Divide by 1.
to
255: Divide by 255.

0x00

31:8

-

Reserved

0x00

Table 27.

UART clock divider register (UARTCLKDIV, address 0x4004 8098) bit description

Bit

Symbol

Description

Reset value

7:0

DIV

UART_PCLK clock divider values
0: Disable UART_PCLK. 
1: Divide by 1.
to
255: Divide by 255.

0x00

31:8

-

Reserved

0x00

Summary of Contents for LPC1311

















































































































































































































































































































































































Reviews:

No comments