nvent JBS-100-STB Installation Instructions Manual Download | Manualshive

Page: 8 / 8

background image

nVent recommends the use

of a conduit drain to prevent

water condensation build-up.

Make sure

conductors are

not exposed.

Conduit

drain

3/4 in locknut

Water tight

conduit seal

Weather seal

17

18

• Install conduit and fittings as shown.

To minimize loosening due to pipe

vibration, use flexible conduit.

• Pull in power and ground wires, strip

off 1/2 in (13 mm) of insulation and

terminate.

•  Install lid.
•  Apply insulation and cladding.
•  Weather-seal the stand entry.
•  Leave these instructions with the end user for future

reference.

nVent.com

North America

Tel +1.800.545.6258

Fax +1.800.527.5703

[email protected]

Europe, Middle East, Africa

Tel +32.16.213.511

Fax +32.16.213.604

[email protected]

Asia Pacific

Tel +86.21.2412.1688

Fax +86.21.5426.3167

[email protected]

Latin America

Tel +1.713.868.4800

Fax +1.713.868.2333

[email protected]

©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specifications without notice.
Raychem-IM-H57741-JBS100STB-EN-1805

PN P000000363

«
...
6
7
8

Summary of Contents for JBS-100-STB









Reviews:

No comments

Related manuals for JBS-100-STB

Brand: Intermatic Pages: 2

Brand: Dewenwils Pages: 2

Signet 2760 DryLoc

Brand: Nivetec Pages: 8

Brand: ACV Pages: 11

Brand: Maretti Pages: 2

Brand: Patton electronics Pages: 12

Brand: Xantech Pages: 2

MINI DMX SPLITTER

Brand: JBSYSTEMS Light Pages: 13

RG-6 Extension Cable PRO-100

Brand: Antex electronics Pages: 1

Digiruler PL20C series

Brand: Magnescale Pages: 84

Brand: Stahl Pages: 85

Brand: PureTools Pages: 12

Brand: Choetech Pages: 21

Brand: IDK Pages: 66

Brand: Mitsubishi Electric Pages: 2

Brand: Philips Pages: 9

Brand: Philips Pages: 2

600 A 15 kV class T-OP II

Brand: Eaton Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands