background image

NuPower

TM

 15D05A-C01-S01 User Manual    

 

 

 

Rev 1.0 

4

 

HARDWARE INTERFACE  

 

The RF Input connector is SMA (female). 

 

The RF Output connector is SMA (female). 

 

The pin-out definitions for the 9 pin Micro-D socket connector are provided in Table 5. In a typical 

installation, the PA module is mated to a host controller board via a cable harness. 

 

 

The RF Out SMA connector is the antenna connection. This connection should always 

be loaded into 50 

Ω

, otherwise the PA could be damaged. 

4.1

 

INTERFACE CABLE HARNESS    

The cable harness that connects the host controller to the 9 pin Micro-D connector of the NuPower 

15D05A-C01-S01 is made up of 9 wires.  

 

Table 5: NuPower 15D05A-C01-S01 Interface Pin-Out Definitions 

Pin No. 

Pin Name 

I/0 

Description 

3, 4, 5 

V Supply 

Primary Power (+28 VDC) 

1, 2, 6, 8 

GND 

Signal and Power Ground 

7* 

Temp Flag 

Over-temp Indicator 

(Low = temperature fault) 

RF Enable 

Transmit Control 

 

 

Figure 4: Micro-D Socket Locations 

 
*Do not connect the Temperature Flag to DC Power (+28 Volts input). The Temperature Flag can be used 

to monitor thermal shutdown. 

Summary of Contents for NUPOWER 15D05A-C01-S01













Reviews: