Nuvo Concerto NV-I8DMS User Manual Download Page 3

FRENCH

Danger 

L‘exposition a des niveaux eleves de bruit peut provoquer une perte 

permanente de l’audition, Chaque organisme humain reagit 

differemment quant a la perte de l’audition, mais quasiment tout le 

monde subit une diminution de I’acuite auditive lors d’une exposition 

suffisamment longue au bruit intense. Les autorites competentes en 

reglementation de bruit ont defini les expositions tolerees aux niveaux 

de bruits: 

8  6  4 3 2 1

DURE EN HEURES PAR JOUR 

INIVEAU SONORE CONTINU EN dB  90  93  95  97 100  103 

Selon les autorites, toute exposition dans les limites citees ci-dessus, 

peuvent provoquer certaines pertes d’audition. Des bouchons ou 

protections dans l’appareil auditif ou sur l’oreille doivent etre portes lors 

de l’utilisation de ce systeme d’amplification afin de prevenir le risque 

de perte permanente de l’audition, Dans le cas d’expositions 

superieures aux limites precitees il est recommande, afin de se 

premunir contre les expositions aux pressions acoustiquese I evees 

potentielIement dangeure u ses, aux personnes exposees aux 

equipements capables de delivrer de telles puissances, tels ce 

systeme d’amplification en fonctionnement, de proteger l’appareil 

auditif. 

ATTENTION: 

AFIN DE LlMlTER LE RISQUE DE CHO ELECTR/QUE, NE 

PAS ENLEVER LE CHASSIS. NE CONTIENT PAS DE 

PIECES POUVANT ETRE REPAREE PAR L’UTILISATEUR. 

CONFER LE SERVICE APRES-VENTE AUX 

REPARATEURS 

ATTENTION 

RISQUE DE CHOC ELECTRIQUE 

NE PAS OUVRIR. 

CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE 

DE VOLTAGE DANGEREUX NON-ISOLE A L'INTERIEUR DE CE PRODUIT 

QUI PEUT ETRE DE PUISSANCE SUFFISAMMENT IMPORTANTE POUR 

PROVOQUER UN CHOC ELECTRIQUE AUX PERSONNES. 

CE SYMBOLE A POUR BUT D'AVERTIR L'UTILISATEUR DE LA PRESENCE 

D'INSTRUCTIONS D'UTILISATION ET DE MAINTENANCE DANS LES 

DOCUMENTS FOURNIS AVEC CE PRODUIT. 

AFIN DE REDUIRE LES RISQUÉ D'INCENDIE ET DE DECHARGE 

ELECTRIQUE, NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A 

L'HUMIDITE. 

IMPORTANTES INSTRUCTIONS DE SECURITE 

1.� Lire avec attention toutes les recommandations et précautions 

d'emploi avant d'utiliser ce produit. 

2.� Toutes les recommandations et précautions d'emploi doivent être 

conservées afin de pouvoir s'y reporter si nécessaire. 

3.� Lire et comprendre tous les avertissements énumérés dans les 

précautions d'emploi. 

4.� Suivre toutes les précautions d'emploi pour utiliser ce produit. 
5.� Ce produit ne doit pas être utilisé près d'eau, comme par exemple 

baignoires, éviers, piscine, sous-sol humides ... Etc. 

6.� Utiliser exclusivement un chiffon sec pour nettoyer ce produit. 
7.� Ne bloquér aucune ouverture de ventilation. Ne pas placer le 

produit tout contre un mur ou dans une enceinte fernée, cela 

gênerait le flux d'air nécessaire au refroidissement. 

8.� Ne pas placer le produit près de toute source de chaeur telle que 

radiateurs, arrivées d'air chaud, fourneaux ou autres appareils 

générant de la chaleur (incluant les amplificateurs producteurs 

de chaleur) . 

9.� Ne pas négliger la sécurité que procure un branchement polarisé 

ou avec raccordement à la terre, Un branchement polarisé 

comprend deux fiches dont l'une est plus large que l'autre. Un 

branchement à la terre comprend deux fiches plus une troisième 

reliée à la terre. Si la fiche secteur fournie ne s'insert pas dans 

votre prise de courant. consulter un 'électricien afin de remplacer 

votre prise obsolète. 

10. Protéger le cordon d'alimentation de tout écrasement ou 

pincement, particulièrement au niveau des fiches, des 

réceptacles utilisés et à l'endroit de sortie de l'appareil. Ne pas 

casser la fiche de terre du cordon d'alimentation. 

11. Utiliser uniquement les accessoires spécifiés par le constructeur. 
12. Débrancher cet appareil lors d'orages ou s'il n'est pas utilisé 

pendant une longue période. 

13. Des précautions doivent être prises afin qu'aucun objet ne tombe 

et qu'aucun liquide ne se répande à l'intérieur de l'appareil par 

les orifics de ventilation ou n'importe quelle autre ouverture. 

14. Pour toutes interventions techniques s'adresser à un technicien 

qualifié.L'intervention technique est nécessaire lorsque l'appareil 

a été endommagé de n'importe quelle façon, comme par 

exemple si le cordon secteur ou sa fiche sont détériorés,si du 

liquide a coulé ou si des objets sont tombés à l'intérieur de 

l'apparei1,si l'appareil a été exposé à la pluie ou à l'humidité, s'il 

ne fonctionne pas normalement ou s'il est tombé. 

15. ATTENTI0N:Pour réduire le risque d'incendie ou de choc 

electrique ne pas exposer l'appareil à la pluie ou à l'humidité. 

Summary of Contents for Concerto NV-I8DMS



































Reviews: