Clean the Baby Monitor with a slightly damp cloth or with an anti-static cloth.
Never use cleaning agents or abrasive solvents.
Do not clean any part of the product with thinners or other solvents and
chemicals – this may cause permanent damage to the product which is not
covered by the warranty.
Keep the Baby Monitor away from hot, humid areas or strong sunlight, and don’t let it get wet.
If something does go wrong, please do not try to repair it yourself – contact Customer Service for assistance
CLEANING
PARENT UNIT
Switch on the unit by Long Press of button 1. The POWER indicator
will show STEADY GREEN. If this indicator starts FLASHING GREEN, the
battery level becomes low.
Charge up the Li battery using the supplied USB cable.
The LED level meter will show the battery status for around 3 sec while
switching on, then resumes to show the received signal level from
baby unit.
Under normal operation, short press button 1 at any time to show the
battery status on the LED level meter.
Place the Parent Unit at a certain distance away from Baby Unit to avoid feedback. Too short distance will
create a screeching sound at the speaker.
Once the Parent Unit receives a signal, the LEDs in the level meter will light up. The louder the baby’s voice,
the more number of LED will be lighted up. This feature is useful to alert the parents of baby’s cry in case the
volume of speaker is turned low to keep the environment quiet,
The speaker volume can be adjusted using the button 2. The LED level meter will show the setting. More LEDs
light up means higher volume (maximum 5 LED). When no LED lights up, the speaker 5 is totally muted. Press
UP button to increase and DOWN button to reduce volume.
Once the Parent Unit is beyond the communication range of the Baby Unit for over 30 sec, an OUT OF RANGE
alarm will be heard together with all LEDs of level meter start flashing to alert the parents. The alarm will only
go off when the Parent Unit comes back within the communication range of BU.
To turn off the alarm sound, press either UP or DOWN of button 2 . The LEDs of level meter still keep flashing
until the Parent Unit falls within the communication range of BU.
Note: This alarm will also be heard in case the Baby Unit is switched off, or its battery has run down, or
its power is cut off.
Each time button is pressed, a beep tone will be heard to validate your press being recognized by the unit.
Both the Baby Unit and Parent Unit can be carried be around using the belt clip. To remove the clip, follow the
diagram below.
At the end of the product lifecycle, you should not dispose of this product with normal household waste.
Take this product to a collection point for the recycling of electrical and electronic equipment. The symbol on
the product, user’s guide and/or box indicates this. Some of the product materials can be reused if you take
them to a recycling point. By reusing some parts or raw materials from used products you make an important
contribution to the protection of the environment. Please contact your local authorities in case you need more
information on the collection points in your area.The internal battery should be disposed of with the Parent
unit in an environmentally-friendly manner according to your local regulations.
DISPOSAL OF THE DEVICE (ENVIRONMENT)
TROUBLESHOOTING
Baby Unit has no transmission
Always showing low battery alert
Many static noise and interference
Too short communication range
Baby Unit always on
Out-of -range alarm always on
Mic sensitivity is too low
Night light is permanently
switched on
Battery life is short
Battery has run down
Baby Unit is located near other
electrical appliances
Many steel structures between
Baby Unit and Parent Unit
Baby Unit battery has run down
Mic sensitivity is too high
Baby Unit battery has run down
Distance between Baby Unit and
Parent Unit exceeds the operating
range
Pairing is not successful
Battery has run out or USB cable
improperly connected
Battery pack is damaged
Adjust mic sensitivity higher using
up button 8.
Switch off night light
Recharge battery using USB cable
(PU) or replace with new battery
or use USB cable connecting to
5V supply.
Remove the electrical appliances
or re-locate the Baby Unit far away
from source of interference.
Re-locate Baby Unit & PU
Replace with new battery or use
USB cable as power supply
Adjust mic sensitivity lower using
down button 8 such that Baby
Unit become voice activated.
Replace with new battery or
use USB cable connecting to 5V
supply.
Move the Baby Unit and Parent
Unit closer together.
Perform pairing again.
Replace with new battery or check
connection
Replace with new battery pack
PROBLEM
POSSIBLE CAUSES
SOLUTION
