BABY UNIT
Slide open the battery door. Insert 3 x AAA size
alkaline batteries (purchase separately) into the
compartment. Observe correct polarities indication.
N.B. For best performance, do not mix use old
and new batteries or alkaline and rechargeable
batteries.
Connect the supplied cable to USB power source,
make sure the polarity is correct. The power supply
from the alkaline battery will be cut off once the
micro-USB plug is inserted into Baby Unit USB port.
1.
2.
Power with batteries
Operation using USB cable
(normally it takes around 4 hours), the POWER indicator turns
steady RED ( if unit is switched on ) or POWER indicator off (if
unit is switched off). Either you can disconnect the cable or keep
connecting will cause no damage to the battery. In the latter
case, when the battery is being consumed and voltage falls to a
certain level, the Lithium battery will automatically be charged
up again.
Note: Before using the parent unit for the first time, charge
up the Li polymer battery for at least four hours.
BABY UNIT
PARENT UNIT
CONTROL LAYOUT
1.
2.
3.
4.
Power ON/OFF switch
Up/Down button
Power/battery low
indicator
LED level meter
5.
6.
7.
8.
Speaker
USB port
Power ON/OFF switch
Up/Down button
9.
10.
11.
12.
Power/battery low
indicator
Transit indicator
Night light switch
Microphone
13.
14.
15.
USB port
Night light
Night light VOX
indicator.
This process is to match the Parent Unit with Baby Unit so that they can communicate with each other while no
other devices (even baby monitor of identical model) can interfere with you or receiving your signal.
The Parent Unit and Baby Unit are already paired when they are manufactured. However, in case you still
encounter interference, perform pairing again to achieve better privacy and signal quality.
PAIRING
1.
2.
3.
4.
5.
6.
7.
8.
Make sure both units are switched off.
Press Hold “DOWN” on button 2 of Parent Unit.
Long Press button 1. The POWER indicator should start FLASHING GREEN. Release both buttons.
Press hold “DOWN” on button 8 of Baby Unit.
Long Press button 7. The POWER indicator should start FLASHING GREEN. Release both buttons.
Press again “DOWN” on button 8 of Baby Unit, if pairing is successful, two beep sound will be heard in
Parent Unit. The POWER indicator of both Baby Unit and Parent Unit should show STEADY GREEN.
The baby monitor is now ready for operation and probably a feedback noise will be heard in speaker of
Parent Unit.
In case the Parent Unit and Baby Unit cannot communicate with each other, repeat pairing process again.
Place the Baby Unit about 1 metre from the crib with
the microphone facing towards the baby. Switch
on the unit by Long Press of button 7, the POWER
indicator will show STEADY GREEN. If this indicator
starts FLASHING GREEN, the battery level becomes
low. Connect the supplied USB cable to a USB power
source.
Adjust the microphone sensitivity using the button
8 to acquire your desirable loudness level. The
TRANSMIT indicator will blink everytime these buttons
are pressed, more number of blinks means the
microphone is more sensitive to sound (maximum is
5 blinks and minimum is 1 blink). Press UP to increase
and DOWN to reduce microphone sensitivity.
Once Baby Unit is in transmit mode, the TRANSMIT
indicator turns RED. The unit will return standby mode
a few seconds after the microphone stops picking up
any sound and the TRANSMIT indicator goes off.
The NIGHT LIGHT (NL) can be set to permanently ON
or VOX mode ( voice activated ) by short press of the
button 11 in following method:
OPERATION
BABY UNIT
NIGHT LIGHT OFF
NIGHT LIGHT ON LEVEL 1
NIGHT LIGHT ON LEVEL 2
NIGHT LIGHT ON LEVEL 3
NIGHT LIGHT ON LEVEL 3 VOX MODE
NIGHT LIGHT OFF
Press button 11
Press button 11
Press button 11
Press button 11
Press button 11
Under VOX mode, the VOX indicator 15 will light up. Once the microphone picks up a sound, the night light will
be on and will fade off automatically a few seconds after the microphone stops picking up any sound.
