Baby breathing mat
EN
3015
M
AT
POWER SUPPLY
BABY BABY MOTION SENSOR MAT (SOLD SEPARATELY)
Slide the lock lever to OPEN position, Slide Open the battery door in direction
as shown. Observe correct polarities, Install 3 pcs AAA alkaline batteries. Slide
Close battery door and Slide the lever back to lock position. Under normal
operation, the battery can last for up to 50days.
CONTROLS LAYOUT
BABY MOTION SENSOR MAT
19.
20.
21.
Movement indicator
Movement sensitivity knob
Alarm hold buttom
PAIRING
PAIRING BABY MOTION SENSOR MAT
10.
11.
12.
13.
The pairing between BU and Baby Motion Sensor Mat should be performed after the successful pairing
between BU and PU or otherwise the system will not operate properly.
Set the BU into pairing mode by repeating step 3 above.
While pressing down the alarm hold button 21 on Mat, switch on the Mat by turning the knob 20 clockwise,
now release hold button 21. Press the feeder timer button 4 on BU, the TRANSMIT indicator shows steady
on and beep sound 2 times will be heard from the BU, indicating the pairing is successful. In case you have
2 Baby Motion Sensor Mats to be paired to two BU, Please pair each one in turn with the other BU being
switched off.
Switch off both the BU and sensor mat, then switch on again for normal operation, probably you will hear
the abnormal breathing alarm in PU after 20 sec in case nothing is placed on the Baby Motion Sensor Mat.
Slight tap the mat few times and the alarm will stop, this shows the system is working properly.
Note: When it is no longer necessary to monitor the baby’s breathing as he grows older, the Baby
Motion Sensor Mat is required to unpair from BU to avoid false alarm. To achieve this perform
pairing process again between PU & BU by repeating above steps 1-8, but leave out steps 11-13.
HOW TO USE
BABY MOTION SENSOR MAT
1. Place the Baby Motion Sensor Mat underneath the mattress, lengthwise direction and directly under where
your baby sleeps. For optimum performance, there should be no bedclothes tucked between the sensor
mat and the mattress. Besides, if the mattress support is too soft (such as box spring or underpadding),
a hard board is required to be placed underneath the mat to provide a firm surface for it. The size of the
board should be larger than the sensor mat.
CORRECT
INCORRECT
2.
3.
4.
5.
6.
7.
8.
With the baby placed in crib, switch on sensor mat by turning the Knob in clockwise direction. Adjust the
position of Knob so that the movement indicator will blink in pace with the breathing movement of baby.
Slip the control box underneath the mattress to keep out of reach of baby and place it as away from the
senor mat as far as possible. According to the change in weight as baby grows, it may be necessary to
adjust the sensitivity setting of Knob again. In case the sensitivity setting is not appropriate, the movement
indicator will always stay ON or OFF and false alarm may occur.
Note: Before attempting to adjust the Knob, wait for at least 15 -20 min until the baby has settled
down or fallen asleep.
For environment with continuous vibration from the floor, the sensor mat may have false detection and
delay or affect the alarm trigger. Under such circumstance, move the crib to the corner of the room or near
a solid supporting wall. Moreover, keep the crib away from strong draft and air current.
Make sure the BU and sensor mat is within the same room or apart from each other not more than a
distance of 10m, otherwise they may lose connection with each other and breathing movement of baby
cannot be monitored.
When parents need to take baby out from crib for feeding or other purpose, to avoid breathing alert alarm,
short press the Alarm Hold button on the sensor mat. This button can be pressed before or after taking out
the baby, but such action must be performed within 20 sec, or otherwise the alarm would still be triggered.
To stop alarm in PU, short press hold Alarm Hold button again.
Upon placing back the baby into crib, the sensor
mat will automatically resume monitoring the
baby movement after 20 seconds.
When the baby’s movement increases as he grows
older, he may move away from the sensor mat and
cause false alarm. Additional Baby Motion Sensor
Mat can be connected to increase the coverage.
Note: In case there are two BUs operating
in the system, make sure each BU and its
corresponding sensor mat are far away from
each other and placed in separate rooms to
avoid interfering each other and creating
false alarm.
