Package
Overview
Installation
1
2
3
4
Warning
and
Caution
■
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not be
responsible for any problems caused by unauthorized repair or maintenance.)
■
Do not allow water or liquid intrusion into the camera.
■
In the use of the product, you must be
in
strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on wall
or ceiling, the device shall be firmly fixed.
■
Do
not
use
camera
beyond
specified
voltage
range
.
■
Do not drop the camera or subject it to physical shock.
■
Avoid touching the camera lens
.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
■
Avoid pointing the camera towards the sun or other light sources.
■
Do not place the camera in extremely hot, cold (the operating temperature shall
be
-22
˚
F~14
0
˚
F
), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
■
To avoid heat accumulation, good ventilation is required for operating
environment.
Camera
Quick
start
guide
Plastic
plug
×4
Drill
template
Allen Key
4 tapping screws
■
Please read th
e
s
e
instruction
s
carefully before using the product and keep it
for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without notice.
■
Visit nuvico.com for additional downloads, manuals, and resources.
2
1
3
1
Ethernet
Connector
2
Audio Input (MIC)
3
Audio
Output (HP)
4
Alarm Input/Output
5
DC12V Power
Connector*
6 Zoom-*
7 Zoom+ *
8 Micro SD Card Slot
9 Reset
10 CVBS Interface (unavailable)
*
If
the
PoE
switch is
used
to
power
the
camera
,
DC12V
power supply
is not required
.
*
It
is
recommended
to
install
the
security cap for outdoor installation.
①
②
Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Trim Ring
∅
4
.6
mm
3
.
55 in
3.55 in
Figure 1
Figure 2
1
3
4
5
9
9
6
7
8
8
10
2
A
L
A
R
M
4 3 2 1
Se
cu
ri
ty c
ap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
A
L
A
R
M
4 3 2 1
Sensor
IPC
ALARM-INA
ALARM-GND
Alarm
Input
:
3
4
Alarm
Power
IPC
ALARM-COM
ALARM-OPEN
+
+
-
-
Alarm
Output
:
1
2
►
Connecting
Alarm Input/Output
(Type A)
(Type B)
*
Only some models support T/W button. If your camera doesn’t have these two buttons, please
skip 6 and 7.
NCT-
8
ML
2
-OV21AF
Vandal Dome
Camera
Quick Start Guide
Rotate the trim ring
counter-
clockwise to remove it from the camera.
Camera Installation
►
►
Connecting Network Cable
Rubber plug
①
②
Loosen the
nut from the main element.
R
un the network cable (without the RJ45 connector) through
both elements. Then crimp the cable with the RJ45 connector.
③
Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.
Before you start, please make sure that the wall or ceiling is strong
enough to withstand three times the weight of the camera. Please install
the camera in a dry environment. Be sure to install the cover or lower
dome back within 4 hours after removing it
. Do not remove the protection
film until
the installation
is completed
.
