NUTRIBULLET PRO+, User Manual

Page: 5 / 18

of your NutriBullet ® or create safety hazards. When replacing blending
containers or an extractor blade or ordering additional accessories from
NutriLiving.com, or by contacting Customer Srevice, please specify the
model for parts that are compatible with your unit.
• Periodically inspect NutriBullet ® components for damage or wear that may
impair proper function. Discontinue use and replace components if you detect
cracking, crazing or cloudiness or other damage to the plastic, tabs and the
Actuators or the Power Base. You may purchase new blending containers and
extractor blades at NutriLiving.com or by contacting Customer Service.
WE
RECOMMEND REPLACING YOUR EXTRACTOR BLADE ® EVERY 6 MONTHS
OR AS NEEDED FOR OPTIMAL PERFORMANCE.
NUTRIBULLET CLEANING
& USER MAINTENANCE INSTRUCTIONS
• Cleaning the NutriBullet ® is so easy...simply place any of the pieces
(except for the Power Base and Extractor Blade) on the top shelf of the
dishwasher or hand wash with warm soapy water and rinse.
HERE’S HOW TO CLEAN THE NUTRIBULLET
®
:
• STEP 1: The most important thing — ALWAYS POWER OFF and UNPLUG
the Power Base from the power supply outlet when it is left unattended,
before assembling, disassembling, changing accessories or approaching
parts that move in use or when cleaning.
Do not attempt to handle the
appliance until all parts have stopped moving!
•
STEP 2:
Make sure the Blending Container / Extractor Blade is not
attached to the Power Base.
•
STEP 3:
Cleaning the individual components (Power Base, Extractor
Blades, NutriBullet Blending Containers):
POWER BASE:
For the most part, the Power Base doesn’t really get dirty, but if you
neglect to twist the Extractor Blade on to the Blending Container tightly,
liquids can leak out and get into the base and stick to the activator buttons.
• NEVER Submerge the Power Base in water or put it in the dishwasher.
• Do not remove the rubber or plastic liners inside the Power Base.
• Use a sponge or dish cloth dampened with warm soapy water to wipe
down the inside well and outside of the Power Base until clean.
• Pay particular attention to the white actuator tabs on the inside of the
Power Base to loosen any sticky debris from drips and spills. If necessary
you may use a small brush to scrub the area to ensure it is kept clean.
EXTRACTOR BLADES:
• Do not wash the Extractor Blade in the dishwasher as elevated
temperatures will warp the plastic and damage the Gaskets.
• Rinse the Extractor Blades in warm water immediately after each use to
prevent debris from drying on the blades and gasket. Use a dish brush to
loosen any debris if you are not going to give it a complete wash at that time.
• When you are ready to thoroughly clean the Extractor Blades, HAND
WASH them in warm soapy water. Give it a quick scrub with a dish brush
to loosen any debris.
• DO NOT REMOVE THE GASKET as this may permanently damage
the Extractor Blade and cause leakage. If after washing as indicated
additional disinfecting is desired, you may rinse with a 10% vinegar/water
solution or with lemon juice. If, over time, the gasket becomes loose or
damaged, you may order new Extractor Blades at NutriLiving.com or
contact Customer Service for a replacement NutriBullet
®
Extractor Blade.
• Dry the Extractor Blades completely. It is helpful to turn the blade on its
side in your dish drainer to ensure BOTH SIDES of the Extractor Blade are
completely dried.
• We recommend replacing your NutriBullet
®
Extractor Blade every 6
months or as needed for optimal performance. To order a replacement
Extractor Blades, simply visit: NutriLiving.com.
NUTRIBULLET ® BLENDING CONTAINERS (CUPS, LIDS AND LIP RINGS) :
• These items are all TOP RACK dishwasher safe. We recommend rinsing
them and giving them a quick brush with a dish brush to remove any dried
debris before washing them in the dishwasher. NEVER use the sanitize
cycle to wash the Blending Containers as this may warp the plastic.
STUBBORN CLEAN UP
• If ingredients dry inside the NutriBullet ® Cups, make your cleanup a snap
by filling the Blending Container about 2/3 full with room temperature
(21°C/70°F or less) water and screw on the Extractor Blade. Place the
Blending Container/Extractor Blade assembly on the NutriBullet
®
Power
Base for about 20-30 seconds. This will loosen the stuck ingredients, and
with a light scrub and rinse, you’ll be all done.
CLEAN FOLLOWING A LEAK:
• To clean the power base: POWER OFF and UNPLUG the Power Base, pick
it up and pour out any excess spillage into the sink. Then use a sponge
or dish cloth dampened with warm soapy water to wipe down the inside
well and outside of the Power Base until clean.
• Pay particular attention to the white actuator tabs on the inside of the
Power Base to loosen any sticky debris from drips and spills. If necessary
you may use a small brush to scrub the area to ensure it is kept clean.
IF YOU HAVE ANY COMMENTS, QUESTIONS OR
CONCERNS, PLEASE GO TO NUTRILIVING.COM
OR CALL CUSTOMER SERVICE AT: 1-800-523-5993 .