NUTOOL MP750N, Manual

Page: 14 / 60

14
GB
• Take good care of your tool. Check that moving parts
properly function and do not jam, that parts are not
broken off or damaged in any way and that the tool
can be used to its full capacity. have damaged parts
repaired prior to using the tool.
The cause of many accidents can be traced back to poorly
maintained electric tools.
• Keep your blades sharp and clean.
Properly maintained blades with sharp edges jam less
frequently and are easier to use.
Make sure to use electric tools, accessories, attachments,
etc. in accordance with these instructions. Take the
conditions in your work area and the job in hand into
account.
Using electric tools for applications other thanthose
intended can lead to dangerous situations.
5 SERVICE
Have your tool repaired only by authorized specialists using
original replacement parts.
This will ensure that your tool remains safe to use.
Special safety instructions
CAUTION
Always secure the workpiece if possible: Use clamps or a vise
to hold the workpiece securely. This is far safer than holding it
in your hand and also means that you have both hands free to
operate the electric tool.
• Ensure that there are no foreign objects adhering to the
workpiece in order to avoid damaging the electric hand plane.
• Hold the tool by its handle using both hands and place the
front base plate of the plane on the workpiece. The base
plates must evenly rest on the workpiece during the planing
process.
• Allow the tool to reach its maximum operating speed
before you start to plane.
• Let the plane run to a complete stop before you set the
tool down. An exposed knife block can catch the surface,
lead to loss of control and, ultimately, serious injury.
• Set the planing depth to 0 mm when you have finished
working.
• Replace used planing knives with a set of new knives
when worn down.
• Some types of planing knives have two blades.
When one blade has become blunt, the planing knife can
be turned over.
• Blunt planing knives cannot be resharpened.
• Always ensure that you replace both knives at the same
time.
• Only the original, manufacturer-approved knife block may
be used for this electric hand plane.
• Always use only clean and sharp planing knives to ensure
professional, safe results.
Do not lose these safety regulations
OPERATING INSTRUCTIONS
Important!
When using equipment, a few safety precautions must
be observed to avoid injuries and damage. Please read
the complete operating manual with due care.
Keep this manual in a safe place, so that the information is
available at all times. If you give the equipment to any other
person, give them these operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions and
the safety information.
1 SAFETY INFORMATION
CAUTION
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury. Keep all safety regulations and
instructions in a safe place for future use.
2 LAyOUT (FIgS. 1/2/3)
1 Setting knob for the chip depth
2 Dust bag
3 Safety lock-off
4 ON/OFF switch
5 Rear base plate
6 Belt cover
7 Chip ejector
8 Front base plate
9 Changeover switch for chip ejector (MP750N only)
10 Power cable
11 Thumb screw for step depth scale
12 Step depth scale
13 Parallel stop
3 PROPER USE
The hand-held electric plane is designed for planing,
rabating and chamfering pieces of wood.
The machine is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be liable for
any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications. Our
warranty will be voided if the machine is used in commercial,
trade or industrial businesses or for equivalent purposes.
4 TECHNICAL DATA
MP750N MP900N
Mains voltage 230-240 V ~ 50 Hz 230-240 V ~ 50 Hz
Rated power 750 W 900 W
Idling speed 16500 min
-1
16000 min
-1
Chip depth 0 - 2 mm 0 - 3 mm
Rebate depth 0 - 6 mm 0 - 6 mm
Plane width 82 mm 82 mm
Protection class
II / II /
Weight 2,9 kg 2,9 kg