background image

2

GENERAL INFORMATION

PLANNING AND LAYOUT EXAMPLES

The NuTone Central Cleaning System consists of a Power Unit,

PVC Tubing, PVC Fittings, Wall Inlets, a flexible hose and
various cleaning attachments.

As an aid in planning the installation in either new or existing

construction, look at the following examples:

Here the power unit is mounted in the

garage. The intake and exhaust tubing, 
the only exposed
tubing in the
installation, runs 
up the garage wall 
and into the attic. 
The trunk line runs
horizontally through 
the attic from the 
power unit to the 
farthest inlet location.
Branch lines spread
throughout the attic,
connecting the trunk line 
to the inlet tubing. Each inlet tube is threaded 
vertically through an inside wall. Located in hallways, 
and in large rooms, the inlets are placed to provide maximum
access to all cleaning areas. See Figure 1.

In this installation, the power unit is mounted in the basement,

conveniently located for shop use and messy cleaning jobs. The
intake tubing runs up the basement wall and connects to the
main trunk line, which runs along the unfinished basement
ceiling. Two first-floor inlets are connected to the trunk line by
vertical inlet lines run through interior walls. In the center of the
house, a vertical branch line runs from the basement trunk line,
through stacked closets, up into the attic. A second trunk line
runs across the attic and two branch lines connect to inlet
lines which are dropped down through upstairs interior
walls. See Figure 2.

The double-trunk line system is commonly used in 

two-story houses. Finding the “key” to an accessible 
vertical area is the most important step in this kind 
of installation.

The Power Unit is designed to be wall-mounted away from the

living area of the home and connected to the living area by
means of permanently installed in-wall tubing and fittings.

EXHAUST

TRUNK LINE

BRANCH LINE

INLETS

POWER

UNIT

INTAKE

INLET LINE

VERTICAL

BRANCH

LINE

ATTIC

TRUNK

LINE

INLET 

LINE

INLET

EXHAUST

INTAKE

POWER

UNIT

BASEMENT

TRUNK LINE

FIGURE 2

FIGURE 1

THE RANCH STYLE HOUSE

THE TWO-STORY HOUSE

Summary of Contents for CV653

























Reviews: