background image

The standard multiCHAIR 4000 is shown in Figure 1

(multiCHAIR 4200 similar).

Unpack all parts from the shipping carton. Remove all tape

and/or packing from the chair. Keep shipping materials for future
use. Note the location of padding materials and sheet plastic
which protects parts of your chair.

Position the seat frame upside down and install the four legs.

Note that the top of each leg has a machined portion approxi-
mately one inch wide. The back two legs have a 1" offset piece
attached to the ends. Install the back two legs so that the offset
points out at a 45-degree angle and note that the small pin must
mate with the holes in the frame (Refer to Figure 3).

D

The top end of each leg should fit easily into the socket of the

frame. Make sure that the legs slide "home" into the sockets. Use
the included ¼" Allen wrench to tighten the bolts located at the
corners of the frame. For ease of future leg height adjustment,
position each leg in the socket so that the adjustment holes face
outward (Refer to Figure 2).

multiCHAIR 4000

offset leg with pin

seat frame

ASSEMBLY INSTRUCTIONS

!ATTENTION: PLEASE READ!

Please see LIMITED WARRANTY of these instructions. If the warranty is not acceptable, contact Nuprodx, Inc. for information about
returning the chair for a refund (Restocking fees and shipping charges will be applied). This chair is designed and intended for indoor
shower and bathroom use. It is not designed for outdoor use and will void the warranty if used in this fashion. If thresholds, shower
curbs or barriers are encountered that exceed ½” in height, the area in question should be brought within the code for disabled acces-
sibility.

Figure 1

Figure 2

Figure 3

SAFETY PRECAUTION!

If the small pins are not mated with the seat frame correctly there
is an extreme risk of the legs dislodging completely from the
chair. This could cause serious injury or even death!

SAFETY PRECAUTION!

If any of the legs are not fitted correctly into the socket of the seat
frame or are not securely tightened there is an extreme risk of the
legs dislodging completely from the chair. This could cause seri-
ous injury or even death!

Summary of Contents for multichair 4000










Reviews: