background image

Spares

OPUS 30  single fans

ITEM

PART No.

Front grille assembly

770874

Foam Filter  set (all units).

630016

Transformer  assembly

771921

Internal assembly:

RS12 units

771287

OPUS 30  Twin fans

ITEM

PART No.

Front grille assembly

770874

Foam Filter  set (all units).

630016

Transformer assembly 

771285

RA12, RAS12,  and all 2R type units below

771922

Internal assembly:

2RAS12 units

771290

Installation and Maintenance  

OPUS 12V (R range)

5

Installation Notes:

WIRING SIZES
It is important to note that the size of wire used between the
transformer and the fan unit can have an adverse effect on the
units performance if the following table is not adherred to.

Mains supply (240v) ......................0.5mm sq.

TRANSFORMER TO FAN

Cable run

(max. 10m)         

Cable size

Up to 2m ...................................0.75mm sq.

Up to 4m ...................................1.00mm sq.

Up to 6m ...................................1.50mm sq.

Up to 10m .................................2.50mm sq.

Power consumption

Unit

input power (watts). ..............................42.0

Full load current (amps). ................................  4.2

Starting Current (amps).  ...............................   4.4

Transformer

input power (watts)................ 67.0

Full load current (amps). ...............................    .34

Starting Current (amps).  ..............................    .35

Summary of Contents for OPUS 30 R Series









Reviews: