
5
16. 04. 21. Document Number 671965
Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk
HIAQM
Installation Manual
•
Refit switch cover.
Schematic Diagram
Pressure Sensor Internals
2 - NO
3 - C
1 - NC
3 - C Contacts 2 - NO
when the difference between
positive & negative pressure
is equal to the set pressure.
Customer 240 V
Connection
Customer 240V
Connection
Internal Connection
Customer Connection
*Note 1: NC has been
blanked off.
*Note 2: Pressure setting
of 125Pa above clean filter
pressure is recommended.
*Note 3: If a different
arrangement is required,
then the internal LED con-
nections can be removed.
240 V
Indicator
240 V
Indicator
Sensor Diagram
2 - NO
1 - NC
*Note 2
*Note 3
*Note 1
Differential
Pressure
Setting
3 - C
12
Dirty Filter Switch Wiring
3.2.2 Setting Dirty Filter Switch Pressure
Nuaire recommend the pressure switch be set to trigger when the
filters experience a 125 Pa increase above the clean filter resistance for
the largest commissioned airflow rate. Use the adjustment dial to set
the pressure at which the switch will trip. When the pressure falls below
this set value, the switch returns to its resting position.
4.0 MAINTENANCE
It is important that maintenance checks are recorded and that the
schedule is always adhered to, in all cases, the previous report should
be referred to.
4.1 Carbon Filter Maintenance
After a period of time, activated carbon in filter cells will become
saturated by odour, gas and chemical vapour contaminants and will
require replacement in order to maintain the filtration efficiency of the
carbon filter. HIAQM Carbon Filters have a lifespan of 2 years under
normal conditions. However, under certain circumstances, such as
highly polluted air, carbon filters may need to be replaced on a more
frequent basis. Contact Nuaire for accurate assessments of carbon filter
lifespans.
4.2 Routine Maintenance
•
Clean all areas of unit and treat any areas of corrosion.
•
Check all access doors for leakage and if necessary locks should be
adjusted and any replacement gasket materials should be replaced
as required.
4.3 Every 3 Months
•
Check filters and change/clean if required, failure to do so may
impair the performance and energy efficiency of this unit.
4.4 Annually
•
Thoroughly inspect the unit and its components for corrosion,
acting immediately to treat/restore any damaged areas.
4.5 Replacement Filters
To check the filter type within a unit refer to the module product label.
Replacement filters can be purchased direct from Nuaire using the
below code format.
1
-
2
-
3
4
-
5
HIAQM
-
015
-
1
D
-
FILTER
1. Range:
HIAQM
= Haven Indoor Air Quality
Filter
Module
2. Reference Flowrate:
015
= 0.15m
3
/s
025
= 0.26m
3
/s
045
= 0.35m
3
/s
055
= 0.48m
3
/s
065
= 0.58m
3
/s
3. Filter Position:
1
= Primary Panel Filter
2
= Secondary Bag Filter
4. Filter Grade:
A
= G4 / ISO Coarse
B
= M5 / PM10 50%
C
= M6 / PM2.5 50%
D
= F7 / PM1 50%
E
= F8 / PM1 70%
F
= F9 / PM1 80%
G
= Rigid Carbon Panel Unit
(RCP)
For reference on the filter type required please refer to the module
product label e.g. The codes required to order both filters of a
HIAQM-025-S-D-G-11
would be:
HIAQM-015-1D-FILTER
HIAQM-015-2G-FILTER
5.0 WARRANTY
The 5 year warranty starts from the day of delivery and includes parts
and labour for the first year. The remaining period covers replacement
parts only (replacement filters not included).
This warranty is void if the equipment is modified without
authorisation, is incorrectly applied, misused, disassembled, or not
installed, commissioned and maintained in accordance with the details
contained in this manual and general good practice.
The product warranty applies to the UK mainland and in accordance
with Clause 14 of our Conditions of Sale. Customers purchasing from
outside of the UK should contact Nuaire International Sales office for
further details.
Failure to maintain the unit as recommended will invalidate the