NTI SM-8X8-C6HDR-POE-HDBT Operation Manual Download Page 4

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or 

operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this 

equipment:

•  Always follow basic safety precautions to reduce the risk of fire, 

electrical shock and injury to persons.

•  To prevent fire or shock hazard, do not expose the unit to rain, 

moisture or install this product near water.

• 

Never spill liquid of any kind on or into this product.

• 

Never push an object of any kind into this product through any  

openings or empty slots in the unit, as you may damage parts 

inside the unit.

• 

Do not attach the power supply cabling to building surfaces.

• 

Use only the supplied power supply unit (PSU). Do not use the PSU 

if it is damaged.

• 

Do not allow anything to rest on the power cabling or allow any 

weight to be placed upon it or any person walk on it.

• 

To protect the unit from overheating, do not block any vents or 

openings in the unit housing that provide ventilation and allow for 

sufficient space for air to circulate around the unit.

Summary of Contents for SM-8X8-C6HDR-POE-HDBT






















Reviews: