background image

 

 

Press Enter and arrow keys to select one of 
these options:   
 
Automatic 
Manual 
Confirmation  
 
This sets the behavior if an assigned sensor 
is replaced.   
 

Automatic

: (recommended) In case of 

probe replacement the systems assigns 
automatically the new sensor in place of the 
old sensor. 
  

Manual

: In case of probe replacement the 

new probe/sensor  must be searched and 
assigned manually to the measuring point as 
described in Step 1  
 

Confirmation

: (default)  In case of probe 

replacement the system asks for a 
confirmation before assignment of new 
sensor in place of the old sensor 

Step 3: Assign measuring points and parameters to channels 1 to 4  

Analog 

Output equals display 

line 1 

etc.  

 

Enter  

 

 

 

 

 

 

 

 

 

Choose Source : Measuring point A to D  

 

Choose measuring point as assigned in step 2 des Messpunktes  (A to 
D gemäss Schritt 2)  
If a channel is not used, the data source it set to  "None". 
 

  

Choose measuring parameter 
from measuring point  

 

Rel.humidity ( calibration !!)

 

(rel. Feuchte) 

  Temperature  

(Temperatur) 

  Mixing Ratio  

(Mischungsverhältnis) 

 

  Vap. Part. Press.  

(Wasserdampfpartialdruck) 

  Dewpoint  

(Taupunkttemperatur) 

  Spec. Enth.  

(spezifische Enthalpie) 

  Abs. Humidity  

(Absolutfeuchte) 

 

 

Available  parameters  depend  on  assigned  sensor.  Not  all  parameters 
might be available.   
Note:  the  analogue  outputs  are  set-up  according  to  the  selected 
measuring parameter.  
 

Unit 

Measuring  unit  selection  according  to  the  previously  selected 
parameter. 
 

 

Press 

for Menu 

Scroll down 

  

Summary of Contents for Novasina Quantadat TRIPLEX










Reviews: