Novatel DL-V3 Reference Manual Download Page 53

Page: 53 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

• For each destination in the groupuse destination list, an

unlogall

command is issued (for the

particular virtual channel).

• If the groupuse destination list contains any FILE_

destinations, and a site has been defined, a

site leave

command is issued.

• For each FILE_

destination in the groupuse destination list, a

logfile

command is issued,

terminating the associated destination with the logfile.

•

groupposfix

groupposave

configuration is executed.

An OK response to the

groupuse

command does not guarantee that all steps in the

groupuse

sequence have completed successfully.

A response to the

groupuse

command does not guarantee that the sequence has completed

execution. If it is important to guarantee that a subsequent command is executed

after

the entire

groupuse

sequence has been completed, the “Groupuse execution in progress” bit in the Auxiliary

2 status word in the

rxstatus

log, see

Page 94

, should be used.

Syntax

groupuse start|stop

groupname

[

dst

] [

filename

]

Message ID = 149

Table 34: Group Action

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Group Action, see

Table 34 on

Page 53

Enum

none

Group name

Char[]

none

H+4

Serial Port Identifier, see

Chapter

3, Table 55 on Page 76

THISPORT

Enum

none

H+16

Filename

NUL

Char[]

none

H+20

Binary Value

ASCII Value

Description

START

Start the specified group

STOP

Stop the specified group

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands