Novatel DL-V3 Reference Manual Download Page 76

Page: 76 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 3

DL-V3 Logs

Table 55: Serial Port Identifiers

Table 56: Parity

Table 57: Handshaking

Port Identifier

Description

ASCII

Binary

COM1

COM port 1

COM2

COM port 2

COM3

COM port 3

THISPORT

The current COM port

FILE_ALL

All virtual ports which may be associated with
a file on the CF card

ALL

All COM ports

USB1

a. The only other field that applies when a USB port is selected is the

echo field. A place holder must be inserted for all other fields to use
the echo field in this case.

USB port 1

USB2

USB port 2

USB3

USB port 3

AUX

Auxiliary (AUX) port

FILE_0

224

File on the CF card, virtual port 0

...

FILE_31

255

File on the CF card, virtual port 31

Binary

ASCII

Description

No parity

Even parity

Odd parity

Binary

ASCII

Description

No handshaking

XON

XON/XOFF software handshaking

CTS

CTS/RTS hardware handshaking

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands