Novatel DL-V3 Reference Manual Download Page 40

Page: 40 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

Table 22: GROUPDGPSTXID Default Configuration

2.17 GROUPECUTOFF

Edit Group Elevation Cut-Off Angle

The

groupecutoff

command allows you to edit the elevation cut-off angle configuration for the group.

groupecutoff set

sets cut-off for the group named

groupname

ecutoff

groupecutoff clear

removes

the cut-off setting from the group named

groupname. groupecutoff default

sets the elevation cut-off

for the group to 0 degrees.

Syntax

groupecutoff set

groupname

[

ecutoff

]

groupecutoff default|clear

groupname

2.17.1

Groupuse Translation

groupuse start

•

If set, the

ecutoff

command is issued.

groupuse stop

•

N/A

Message ID = 56

Field

Power-On

Freset

Stored in NVM

DGPS Type

no change

AUTO

YES

no change

NUL

YES

Field

Data

Value Used if
Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 22

Page 40

Enum

none

Group name

Char[]

none

H+4

Elevation cutoff

Float

none

H+16

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands