background image

VX4S/VX4 User's Manual 

-17-

9  FAQ

Questions

Methods

LED display is off

Inspect whether the power connection is correct and the switch 

has been turned on;
Play the Self test image and confirm whether the connection of 

LED is correct and works normally;
Inspect whether VX4 output has signal and shows blank screen;
Inspect whether the mode and parameter of screen 

configuration are correct;

Monitoring port 

output is abnormal 

Check whether there is image input in input channel and 

whether it is correctly displayed; 
Check whether PIP has been turned on, whether there is signal 

input in 2 channel and whether it is correctly displayed; 
Check whether monitoring output is connected correctly and it 

is not loose; 
Please confirm whether Monitor supports the output resolution 

of VX4; 
Try to cut off the power of equipment and restart it, reset VX4 

and operate again;

P h a s e   o f   V G A 

input offset

Perform VGA Auto ADJ; 

P I P   d i s p l a y   i s 

abnormal 

Check whether there is signal input in 2 channel and it is 

normally displayed; 

Check PIP and confirm whether parameter setting is normal; 

Fading is abnormal Check whether Switching effect has been enabled;

Image Mosaic is 

abnormal 

Check whether the VX4 Image Mosaic switch has been turned on 

and whether Image Mosaic parameters settings is correct; 

Check whether input signal source is normal; 

Sound is abnormal 

Check whether the volume settings is appropriate;

Check whether the Audio mode setting is correct;

Confirm VX4 is well connected to multifunction card, and the 

corresponding output port icon on the main interface has 

been highlighted; confirm whether the audio output mode of 

multifunction card is HDMI mode (it is required to connect LCT 

for confirmation and setting);  

Please preliminarily investigate problems according to the above steps; if you cannot 
eliminate the problems, please contact the local dealer or our company’s customer 
service personnel.

There is high voltage inside the machine. In order to guarantee your safety, please do 
not maintain the processor by yourself.

Xi’an 

NovaStar 

Tech 

Co., 

Ltd.

Summary of Contents for VX4S





















Reviews: