Novar 738005000 Installation Instructions Manual Download Page 2

FCC Information

This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

NOTE! This equipment has been tested and found to comply with the limits for

a Class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.

CAUTION!

Any changes or modifications not expressly approved by Novar
Controls Corporation could void your authority to operate this
equipment.

Industry Canada

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the interference-causing equipment standard entitled

Digital

Apparatus

, ICES-003, of Industry Canada.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B préscrites dans la norme sur le matériel brouiller:

Appareils Numériques

, NMB-003, édictée par l’Industrie Canada.

Disclaimer

LOGIC ONE

® is a registered trademark of Novar Controls Corporation.

Lingo™ is a trademark of Novar Controls Corporation.

The material in this manual is for information purposes only. The contents and the
product it describes are subject to change without notice. Novar Controls Corporation
makes no representations or warranties with respect to this manual.

In no event shall Novar Controls Corporation be liable for technical or editorial omissions
or mistakes in this manual, nor shall it be liable for any damages, direct or incidental,
arising out of or related to the use of this manual.

Copyright © 2001 by Novar Controls Corporation. All rights reserved.

No part of this manual may be reproduced in any form or by any means

without prior written permission from Novar Controls Corporation.

Novar Controls Corporation

3333 Copley Road, Copley, OH 44321

Tel: (330) 670-1010

www.novarcontrols.com

Summary of Contents for 738005000













Reviews: