Nova NG-250 Instruction Manual Download Page 19

19

1. Ensure the plug is disconnected from the 
mains power supply.
2. Raise the cutting head. 
3. Loosen and remove the cross headed rear 
fixing screw to the 'D' shaped arbor plate (Fig. 
25).
4. Release the lower blade guard operating the 
linkage by loosening and then removing the 
cross headed pivot screw (Fig 26).
5. Operate the lower safety guard release lever.
6. Rotate the lower guard up over the upper 
blade guard (Fig. 27).
7. Rotate the 'D' shaped arbor guard plate 
slightly to give greater access to the machines 
arbor.

Caution: 

Ensure that any spacers and 

spindle rings that may be required
suit the spindle and blade that are fitted.

!

MAINTENANCE

POWER CABLE MAINTENANCE
If the power cable needs replacing, the 
task must be carried out by an electrician 
or a power tool repairer in order to avoid a 
safety hazard.

CHANGING THE BLADE

Warning: 

Always ensure the Mitre Saw 

is switched off and the plug is removed 
before performing any adjustments or 
maintenance procedures.

Caution: 

Never try to use a blade that 

is larger than the stated capacity of the 
Mitre Saw. It might come into contact 
with the blade guards and risk personal 
injury or damage to the Mitre Saw. This 
will not be covered under warranty.

!

!

Caution: 

Never use a blade that is too 

thick to allow the outer blade washer 
to engage with the flats on the spindle. 
It will prevent the blade screw from 
properly securing the blade onto the 
spindle.

!

Fig.25

Fig.26

Fig.27

Rear fixing 

screw

Pivot screw

Summary of Contents for NG-250

























Reviews: