1.0 GENERAL OPERATION
Press POWER key to switch cash counter on
Use and keys to select a required denomination
Place banknotes or coin scoop with coins of the same denomination on the cash counter
Remove to register a count or press ENT
key to abort count
When cash counter is empty, ENT
key can be used to reset running totals as follows:
Press ENT key to reset running totals for current denomination
Press and hold ENT key to reset running totals for all denominations
Use AUTO
key to auto scroll denominations and select scroll direction:
Lower to higher denomination scroll symbol
Higher to lower denomination scroll symbol
Lower to higher and back to lower denomination scroll symbol
Use PRINT
key to display print functions (section 3.0)
Press and hold POWER
key to switch cash counter off
2.0 SETUP MENU
Press and hold POWER key to switch cash counter off. Press ESC key to enter SETUP MENU.
2.1 STANDBY TIME
To save battery power, cash counter will enter standby after a period of inactivity determined by
STANDBY setting. Select shortest practical standby time
Highlight STANDBY setting using
and
keys
Change standby time using and keys
2.2 LCD DISPLAY CONTRAST
Highlight CONTRAST using
and
keys
Use and keys to change LCD contrast to personal preference
2.3 BACKLIGHT TIME
LCD backlight uses significant amount of battery power. To save battery power, the backlight will
be switched off after a period of inactivity determined by BACKLIGHT setting. Select shortest prac-
tical backlight time or disable completely
Highlight BACKLIGHT using
and
keys
Change LCD backlight time using and keys
2.4 SET TIME AND DATE
Highlight SET TIME & DATE using
and
keys
Press ENT key to display current time and date
Use
and
keys to select time or date and press ENT key
Use and keys to change between HRS-MIN-SEC and DD-MM-YY
Press ENT key to set
When finished, press ESC key to exit setup menu
3.0 PRINT FUNCTIONS
Press PRINT key to display PRINT MENU
Print Single: Print running totals for currently selected denomination
Print Total:
Print grand total
4.0 WEIGHING SCALES
Press and hold POWER key to switch cash counter off
Press key to enter weighing scales
Use
and
keys to change engineering units. (Available units: grams, pounds, ounces)
Place up to 3Kg of weight on the scales
Use PRINT key to print the result
5.0 CALIBRATION MENU
Allow 5 minutes warm-up time (cash counter on) before attempting calibration
(In setup menu, change standby time to 10 minutes to stop counter from switching off. When finished,
reduce standby time to save battery power)
If red light is flashing, connect a charger and fully charge cash counter before attempting calibration.
Calibration should be performed while the counter is running of battery power
Place counter on a flat, stable surface. Do not lean or make contact with the surface during calibration.
Make sure the room is free from strong air drafts caused by air conditioning or open windows
To enter calibration menu, press and hold POWER key to switch cash counter off
Press ESC key and select CALIBRATION MENU from SETUP MENU
5.1 CASH COUNTER CALIBRATION
To maintain accuracy, cash counter can be calibrated at any time using a precise 100g weight (not
included)
Select CALIBRATE SCALES from CALIBRATION MENU
Start calibration and follow screen prompts
Use ESC key to abort calibration at any time
On completion, select one of two options:
If any banknotes or coins were previously calibrated, select
CURRENT SETTINGS, otherwise select FACTORY DEFAULTS
5.2 SCOOP CALIBRATION
Cash counter is supplied with a scoop, used only for counting loose coins. To use a different
scoop to the one supplied, it must first be calibrated
Select CALIBRATE SCOOP from CALIBRATION MENU
Start calibration and follow screen prompts
Use ESC key to abort calibration at any time
5.3 BANKNOTES AND COINS CALIBRATION
Cash counter is supplied calibrated for a particular currency and normally does not require recali-
bration
For calibration procedure, refer to a separate document:
http://www.noteandcoin.com/files/NCS2010_Calibration_procedure.pdf
