NorthStar NSC 11 ED Installation, Operation, Maintenance & Repair Parts Download Page 26

Page: 26 / 26

REPAIR PARTS

KEY

NO.

PART

NO.

DESCRIPTION OF PART

7070412 Screw, #4 - 24 x 1-1/8 in.

7117816 Spacer

7030713 Switch

7077472 Expansion Pin

7074123 Screw, #10 14 x 2 in. (5)

7085263 Valve Cover

7082087 Wave Washer

7199232 Rotor & Disc

7199729 Cap

7170262 O-ring Seal, 1.1 in. x 1.4 in.

7167659 Screen Support

7146043 Screen

0521829 Flow Plug

7237721 Nozzle & Venturi, with Gasket

7095030 Cone - Screen

1148800 Fill Flow Plug

7003847 O-ring Seal, 1/4 in. x 1/2 in.

7120526 Elbow

1202600 Nut-Ferrule

7187065 Nozzle & Venturi Assembly

7081201 Retainer

7170319 O-ring Seal, 1/4 in. x 3/8 in. (2)

7082053 Valve Body

7133498 O-ring Seal, 15/16 in. x 1-3/16 in. (2)

7116713 Clip (2)

KEY

NO.

PART

NO.

DESCRIPTION OF PART

7129889 Spring

7092642 Plug (Drain Seal)

7167552 Seal (Nozzle & Venturi)

7133456 O-ring Seal, 3/8 in. x 9/16 in.

7123639 Rotor Seal

7126433 Wear Strip

7133511 O-ring Seal, 3-3/8 in. x 3-5/8 in.

7133472 O-ring Seal, 3/4 in. x 15/16 in.

7133464 O-ring Seal, 7/16 in. x 5/8 in.

0501226 Flow Plug, Bkw. and F. Rinse (NSC17ED)

0501228 Flow Plug, Bkw. and F. Rinse (NSC14ED,

NSC11ED)

7024160 Drain Hose Adaptor

7170327 O-ring Seal, 5/8 in. x 13/16 in.

0900431 Hose Clamp

7142942 Clip

7113927 Cam and Gear

0503288 Bearing

7117808 Motor Plate

0900857 Screw, #6 - 20 x 3/8 in. (2)

7186263 Motor - Includes Key No. 44

7131755 Screw, #6 - 20 x 7/8 in. (2)

0900060 O-ring Seal

7248714 Sensor Housing

7147243 Turbine and Support Assembly

Turbine

Turbine Support

7117858

2204101

Summary of Contents for NSC 11 ED



























Search results

Summary of Contents for NSC 11 ED

Reviews:

Related manuals for NSC 11 ED

Brands by name

Popular brands

NorthStar NSC 11 ED, Installation, Operation, Maintenance & Repair Parts

Search results

Summary of Contents for NSC 11 ED

Reviews:

Related manuals for NSC 11 ED

Brands by name

Popular brands