Northern Lights Lugger M843NW2 Operator'S Manual Download Page 5

OM843NW2  10/09

5

Serial Numbers

Safety Rules

CAUTION:  This symbol is used throughout
this book to alert you to possible danger areas.
Please take special notice of these sections.  

A warranty registration certifi cate is supplied 
with your set. It entitles the original purchaser of our 
equipment to a warranty covering material 
or assembly faults. The extent of coverage is described 
in the Limited Warranty Statement. We recommend 
that you study the statement carefully.

NOTE:

 If the warranty is to apply, the servicing 

instructions outlined in this manual must be 
followed. If further information is needed, please con-
tact an authorized dealer or the factory.

CAUTION:

  Accident reports show that careless use of engines causes a high percentage of accidents. 

You can avoid accidents by observing these safety rules. Study these rules carefully and enforce them on the job.

•  Never leave engine without proper security.

•  Turn the coolant tank cap slowly to relieve pressure 

before removing. Add coolant only when the engine 
is stopped and cool.

• Mount 

fi re extinguisher near engine.

•  Always disconnect the battery ground strap before 

making adjustments.

•  Operate engines in properly ventilated areas.

•  Keep trash and other objects away from engine.

• Escaping 

fl uids under pressure can penetrate your 

skin. Use a piece of cardboard or wood, not your 
hands, to search for leaks.

•  Avoid wearing loose clothing without a belt when 

working around engines.

•  Do not oil or grease engine while it is running.

•  Use caution in handling fuel. Never refuel a hot 

or running engine. Do not smoke while fi lling fuel 
tank or servicing fuel system.

Your set has three serial numbers:  

1

  an engine number stamped 

on the block,  

2

  a generator plate, and  

3

 a generator set plate. 

Use the serial number on the generator set plate when ordering parts 
or in correspondence. The generator set plate is found on the service 
side of the generator and resembles the drawing at left. 

Generator set serial number plate.

Warranty

•  Keep your hands, feet, hair and clothing away from 

power-driven parts.

•  Check for any loose electrical connections or faulty 

wiring.

•  Engines should be operated only by knowledgeable, 

qualifi ed personnel.

•  Look completely around engine to make sure that 

everything is clear before starting.

•  Do not operate an engine that isn't in proper work-

ing order. If an unsafe operating condition is noted, 
tag the set and control panel so others will also 
know about the problem.

• Provide 

fi rst aid kits.

Summary of Contents for Lugger M843NW2



























Reviews: