background image

OM673   09/09

CAUTION:  This symbol is used throughout
this book to alert you to possible danger areas.
Please take special notice of these sections.  

A warranty registration certifi cate is supplied 
with your set. It entitles the original purchaser of 
our equipment to a warranty covering material 
or assembly faults. The extent of coverage is 
described in the Limited Warranty Statement. We 
recommend that you study the statement carefully.

NOTE:

 If the warranty is to apply, the servicing 

instructions outlined in this manual must be 
followed. If further information is needed, please 
contact an authorized dealer or the factory.

CAUTION:

  Accident reports show that careless use of engines causes a high percentage of accidents. 

You can avoid accidents by observing these safety rules. Study these rules carefully and enforce them on the job.

•  Use caution in handling fuel. Never refuel a hot 

or running engine. Do not smoke while fi lling 
fuel tank or servicing fuel system.

•  Keep your hands, feet, hair and clothing away 

from power-driven parts.

•  Check for any loose electrical connections or 

faulty wiring.

•  Engines should be operated only by knowledge-

able, qualifi ed personnel.

•  Look completely around engine to make sure 

that everything is clear before starting.

•  Do not operate an engine that isn't in proper work-

ing order. If an unsafe operating condition is noted, 
tag the set and control panel so others will also 
know about the problem.

• Provide 

fi rst aid kits.

•  Never leave engine without proper security.

•  Turn the coolant tank cap slowly to relieve 
 

pressure before removing. Add coolant only 
when the engine is stopped and cool.

• Mount 

fi re extinguisher near engine.

•  Always disconnect the battery ground strap 

before making adjustments.

•  Operate engines in properly ventilated areas.

•  Keep trash and other objects away from engine.

• Escaping 

fl uids under pressure can penetrate 

your skin. Use a piece of cardboard or wood, 
not your hands, to search for leaks.

•  Avoid wearing loose clothing without a belt 

when working around engines.

•  Do not oil or grease engine while it is running.

Safety Rules

Warranty

3

Summary of Contents for Lugger M673D




































Reviews: