manualshive.com logo in svg

North FRONTIER Series, User Instructions

Share
Download
North FRONTIER Series User Instructions Download Page 20

9.2.2.5  Install facepiece seal: 

Install the lens into the facepiece seal (Figure 33). Gently 

work the lens into the face seal. Ensure the visor is positioned so the facepiece is not
distorted.  Place a small amount of liquid soap around the attaching area of the lens clamp. 
Install the visor clamps and tighten screws.

9.3

REPLACING FACEPIECE HEADSTRAP

9.3.1

The harness assembly is a four point harness. Remove harness assembly by pushing forward
at each attachment point to align the button with the groove and remove the harness from 
facepiece (Figure 34). Repeat at each attachment point.

9.3.2

To remove the headstrap from the buckle (latch and bail assembly), gently work the pull tab of
the headstrap through the bail (Figure 35).

9.3.3

Orientate the new headstrap so the large opening is aligned near the chin opening of the 
facepiece (Figure 36).

9.3.4

To reinstall, ensure the bail is placed on the inside of the latch and feed the pull tab end of the
headstrap through the buckle. The end of the pull tab should facing outward and the ribs 
should engage the buckle. Repeat on the other three sides. Reinstall harness assembly to 
facepiece, locking the buttons into the grooves of the buckle.

9.4 BACKFRAME 

HARNESS

9.4.1

Separate lower strap from upper shoulder strap.

9.4.2

The upper shoulder straps terminate in a “Z“ pattern (Figure 37). Pull one inch of slack 
through the backframe (Figure 38), fold the end of the strap tight against the strap and pass 
the end through the backframe. Repeat on other strap.

9.4.3

Remove waist belt strap in the same manner. Pull one inch of slack and pass the strap 
through the pathway of the strap (Figure 39). Observe the path prior to removal.

9.4.4

Reverse the steps to reinstall.

10.0 FRONTIER OPTIONS

10.1

AIRLINE

10.1.1

The Airline Attachment is located on the left waist belt strap (Figure 40). It is approved with 
Foster, Hansen HK, and Schrader couplings.  Foster, Hansen HK, and Schrader couplings 
include locking devices.

20

NOTE

It is helpful to have a second assembled facepiece for reference during reassembly.

NOTE

It is helpful to have a second assembled backframe for reference during reassembly.

Summary of Contents for FRONTIER Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands