manualshive.com logo in svg

North Star M157310AC.1, Owner'S Manual

Share
Download
North Star M157310AC.1 Owner'S Manual Download Page 22

Operation 

 

22 

 

 

 

 

 

3.

 

Release the collar, making sure it springs back and re-seats to its original 

(non-retracted) position.  (Figure 8b).   

Check the connection by pulling on 

the hose to ensure a positive connection.

 

 

 

 

 

Select spray 
nozzle 

Your pressure washer is equipped with five high-pressure nozzles and one 
low-pressure nozzle.

  Generally, the wider the spray angle of the nozzle, the 

lower the spray impact produced.  Select the appropriate nozzle for the job based 
on the following table: 

 

Color of Nozzle: 

Spray Angle 

Used For: 

Red 

0 

Highest Impact 

Yellow 

15 

Tough Stains/Stripping 

Green 

25 

General 

White 

40 

Light Cleaning 

Black-Low pressure 

65 

Chemicals 

Yellow 

15 

Steam 

 
NOTE: You must use the black low-pressure nozzle for spraying chemicals. 

Attach nozzle 

Attach nozzle to the spray gun. 

 

       

WARNING: 

Depressurize first

 

Any time you remove/install/change a nozzle, you must depressurize hose 
line by squeezing the spray gun trigger while the engine is off.  Even if 
the engine has been off for a long period of time, the hose may remain 
dangerously pressurized. 

 

 

 

 

 

 

 

 

 

 

 

Figure 8a 

 

Correct Insertion 

Not Fully Inserted 

Collar Seated 

Collar NOT Seated 

Figure 8b 

 

Nozzle 

Summary of Contents for M157310AC.1

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands