manualshive.com logo in svg

North American Tool 42801, Operating Instructions Manual

Share
Download
North American Tool 42801 Operating Instructions Manual Download Page 7

7

-Replace oil with SAE 10W30 or
SAE 10W20 non detergent oil
(300ML)
-Drain crankcase and fill to
proper level
-Air pressure regulated too high -
Replace filter

-Improper oil viscosity
-Too much oil in crankcase
-Compressor overheated
-Restricted air filter

Oil discharge in air

-Check for proper adjustment
and if problem persists, replace
pressure switch

-Defective pressure switch or improper
adjustment

Safety valve releasing

-Check valve manually by pulling
upwards on ring. If condition
persists replace valve
-Clean or replace as necessary -
Replace check valve

-Air leak in safety valve
-Restricted air filter
-Defective check valve

Low pressure

-Check voltage, eliminate
extension cord or reset
-Check wiring connections
-Press the reset button or wait for
automatic reset (15 minutes)

-Fuse blown or circuit breaker tripped -
Loose electrical connections               -
Overheated motor

Not starting

Corrective Action

Possible Cause(s)

Symptom

[email protected]

Summary of Contents for 42801











Reviews:

No comments

Brands by name

Popular brands

Load more brands