manualshive.com logo in svg

Nortel CWDM SFP, Installation Manual

Share
Download
Nortel CWDM SFP Installation Manual Download Page 9

 

7

2

Depending on your GBIC model, either grasp the extraction 
tabs (

Figure 1

) located on either side of the GBIC with your 

thumb and forefinger, or lift the extractor handle (

Figure 1

) 

attached to the GBIC.

3

Slide the GBIC out of the Gigabit Ethernet module slot. 

4

If the GBIC does not slide easily from the module slot, use a 
gentle side-to-side rocking motion while firmly pulling the 
GBIC from the slot.

5

Dispose of the GBIC according to all national laws and 
regulations.

GBIC specifications

Table 2

 describes general GBIC specifications.

Note: 

If you are storing a GBIC, remember to place a 

dust cover over the fiber optic bores.

Table 2   

GBIC specifications

Specification

Descriptions

Dimensions (H x W x D)

0.39 x 1.18 x 2.56 inches

(1 x 3 x 6.5 cm)

Connectors

Multimode fiber optic: SC

Single-mode fiber optic: SC

CWGBIC.fm  Page 7  Wednesday, December 12, 2001  11:26 AM

Summary of Contents for CWDM SFP



































Reviews:

No comments

Brands by name

Popular brands

Load more brands