manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 342 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 342

342

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

ARP tab

The 

ARP

 (Address Resolution Protocol) tab shows the MAC addresses and the 

associated IP addresses for the switch.

To open the 

ARP

 tab:

1

From the Device Manager main menu, choose 

Edit > IP

.

The 

IP

 dialog box opens with the 

Globals

 tab displayed 

(Figure 130 on 

page 340)

.

2

Click the 

ARP

 tab.

The 

ARP

 tab opens 

(Figure 132)

.

Figure 132   

Edit IP dialog box — ARP tab

Table 128

 describes the 

ARP

 tab fields.

Table 128   

ARP tab fields

Field

Description

Interface 

The unit and port number.

MacAddress 

The unique hardware address of the device.

IpAddress 

The Internet Protocol address of the device used to represent a point 
of attachment in a TCP/IP internetwork.

Type 

The type of mapping.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments