manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 340 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 340

340

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

To open the 

IP

 dialog box:

➨

From the Device Manager main menu, choose 

Edit > IP

.

The 

Edit IP 

dialog box opens with the 

Globals

 tab displayed.

The following sections provide a description of the tabs in the Edit > IP dialog 
box and details about each item on the tab.

Globals tab

To open the 

Globals

 tab:

➨

From the Device Manager main menu, choose 

Edit > IP

.

The 

IP

 dialog box opens 

(Figure 130)

 with the 

Globals

 tab displayed.

Figure 130   

Globals tab 

Table 126

 describes the 

Globals

 tab fields.

Table 126   

Globals tab fields

Field and MIB 
association

Description

DefaultTTL 

Default value inserted into the Time-To-Live field of the IP header of 
datagrams originated by the switch, whenever a TTL value is not 
supplied by the transport layer protocol. Default value is 64.

ReasmTimeout Maximum 

number 

of seconds that received fragments are held while 

they are awaiting reassembly by the switch. Default value is 60.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments