manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 266 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 266

266

Chapter 7 System configuration using the CLI

320985-A Rev 01

 

The 

default ip domain-name 

command is in the config command mode.

The 

default ip domain-name 

command has no parameters or variables.

Configuration Management

This section covers the following topics:

•

“Automatically loading Configuration file” on page 266

•

“ASCII Configuration Generator” on page 268

Automatically loading Configuration file

This section discusses how to download a configuration file when the system 
boots. You use standard CLI commands to modify the configuration file you want 
to download. This section covers these commands:

•

“configure network command”

•

“show config-network command” on page 267

configure network command

The 

configure network

 command allows you to load and execute a script 

immediately and to configure parameters to automatically download a 
configuration file when you reboot the switch or stack. The syntax for the 

configure network

 command is:

configure network [load-on-boot 

{disable|use-bootp|use-config}] [filename <WORD>] [address 

<XXX.XXX.XXX.XXX>]

The 

configure network

 command is in the exec mode. 

Note: 

When you enter 

configure network

 with no parameters, the 

system prompts you for the script file name and TFTP server address and 
then downloads the script.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments