Nortel 425-24T Configuration Manual Download Page 166

Page: 166 / 488

166

Chapter 4 Getting Started with Device Manager

320985-A Rev 01

Click

Next

If you did not select

Custom

installation in

step 4

, then the

Choose Install

Folder

dialog box opens. Continue with

step 8

page 167

If you selected

Custom

installation in

step 4

, then the

Feature Sets

dialog

box opens (

Figure 49

Figure 49

Feature Sets dialog box

Select which features to install from the feature sets list.

Click

Next

The

Choose Install Folder

dialog box opens (

Figure 50

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Search results

Summary of Contents for 425-24T

Reviews:

Nortel 425-24T, Configuration Manual, Page: 166 / 488

Search results

Summary of Contents for 425-24T

Reviews: