manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 165 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 165

Chapter 4 Getting Started with Device Manager

165

System Configuration Guide

 

3

Click 

Next

.

The 

Choose Install Set 

dialog box opens (

Figure 48

).

Figure 48   

Choose Install Set dialog box

4

Do one of the following:

— Select 

Typical

 installation to install the common set features, as well as 

online help.

— Select 

Minimal

 installation to select minimal features to install 

(recommended for those with limited disk space).

— Select 

Help

 to install only the online help.

— Select 

Custom

 installation to customize the features prior to installation.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments