manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 128 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 128

128

Chapter 3 CLI Basics

320985-A Rev 01

 

Getting help

When you navigate through the CLI, online Help is available at all levels. 
Entering a portion of the command, space, and a question mark (

?

) at the prompt 

results in a list of all options for that command. 

Refer to 

“help command” on page 130

 for more information about the specific 

types of Help.

Basic navigation

This section discusses basic navigation around the CLI and between the command 
modes. As you see, the CLI incorporates various shortcut commands and 
keystrokes to simplify its use. The following topics are covered in this section:

•

“General navigation commands”

•

“Keystroke navigation” on page 129

•

“help command” on page 130

•

“no command” on page 131

•

“default command” on page 131

•

“logout command” on page 132

•

“enable command” on page 132

•

“configure command” on page 132

•

“interface command” on page 133

•

“disable command” on page 133

•

“end command” on page 134

•

“exit command” on page 134

General navigation commands

When you enter “

?

”

 

at any point in the CLI session, the system retrieves help 

information for whatever portion of the command you entered thus far. Refer to 

“help command” on page 130

 for more information.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments