background image

inStallation / PERFoRMancE cHEck liSt

REFRigERation SYStEM

Was unit given 24 hr warm up period 

for crankcase heaters (if applicable)?

YES

NO

Stage-1 Liquid Pressure (high side) ________________________

Stage-1 Suction Pressure (low side) ________________________

Has the owner’s information been 

reviewed with the customer?

YES

NO

Has the Literature Package been left 

with the unit?

YES

NO

inStallation addRESS:

CITY ______________________

STATE _________________

UNIT MODEL # ________________________________________

UNIT SERIAL # _______________________________________

Unit Installed Minimum clearances 

per Figure 1 (page 4)?

YES

NO

inStallER naME:

CITY ______________________

STATE ________________

ElEctRical SYStEM

Electrical connections tight?

YES

NO

Line voltage polarity correct?

YES

NO

Rated Voltage: ___________________________________ VOLTS

L1-L2 Volts: _____________________________________ VOLTS

Has the thermostat been calibrated?

YES

NO

Is the thermostat level?

YES

NO

Is the heat anticipator setting correct? 

(If Applicable)

YES

NO

iMPoRtant

 - This product has been designed 

and manufactured to meet ENERGY STAR criteria 

for energy efficiency. However, proper refrigerant 

charge and proper air flow are critical to achieve 

rated capacity and efficiency. Installation of this 

product should follow the manufacturer’s refrigerant 

charging and air flow instructions. Failure to confirm 

proper charge and airflow may reduce energy 

efficiency and shorten equipment life.

709644a 

(Replaces 7096440)

PRoPoSition 65 WaRning:

WaRning: this product contains chemicals known 
to the state of california to cause cancer.

WaRning: this product contains chemicals known 
to the state of california to cause birth defects or 
other reproductive harm.

Specifications & illustrations subject to change without notice or incurring obligations (05/15).
O’Fallon, MO, © Nortek Global HVAC LLC 2015. All Rights Reserved.

Summary of Contents for P5RF-A





















Reviews: