8
MM271 Installation Instructions
MM271 Installation Instructions
9
1
POWER
ON OFF
SG1
ED1
K1
06
A
VR-ISP
D1
C2
C7
C15
LED3
D15
R20
IC4
D16
D13
D14
K2
BATT
- BA
TT+
STATUS
ANT SHLD
S9.8874
EDGE
COM
LOCK+
LOCK -
PGOK2
00 R
ev. X
C
M_BLK
M_RED
VAR2
GRN
VAR3
VAR3
VAR1
VAR4
VAR5
PF1
VAR6
WHT
GTO Inc.
Tall
aha
sse
e, F
L
CYCLE
EXIT
SAFE
TY
COM
CHGR
CHGR
OFF
120
AUTO CL
OSE
TIME
MIN
MAX
STALL
FORCE
2
3
ON/OFF
SWITCH
4
SETTING CLOSED LIMIT POSITION
TRANSMITTER PROGRAMMING
With gate in the open position, (arm retracted) turn the
control box ON/OFF switch to the off position. Press and
hold the transmitter while sliding the ON/OFF switch to the
ON position and you will hear a single or a series of beeps
followed by a pause then a single beep. At that point release
the transmitter button. This process may take 8 - 10 seconds.
Press and release the learned transmitter button; gate should
start closing. When the gate reaches the desired CLOSED
position, press and release the transmitter button again.
NOTE: If your gate stops and reverses before it fully closes, you
may need to increase the stall force. (See
Press and release the transmitter button again; gate should
start opening. Once the gate reaches the OPEN position, a
single audible alarm will sound to indicate the limit is set.
Gate operator’s closed position is now set. Press and release
transmitter to close gate for normal operation.
WARNING:
Changes, modifications or adjustments not expressly approved by Nortek Security and Control, LLC could void the user’s
authority to operate this equipment. There Are No User Serviceable Parts.
NOTICE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 the FCC. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
3
4
ON/OFF Switch
Replace and secure back cover of the opener remote.
Turn off control box. Press and hold a transmitter button while sliding
the ON/OFF switch to the ON position. Continue to hold transmitter
button for 8 - 10 seconds. You will hear a single or a series of beeps,
followed by a pause then a single beep. Release transmitter’s button.
Your personal code is now programmed.
NOTE
: The button you chose
will be the button used to operate your system.
• An infinite number of the transmitters can be used, provided that
the dip switches are set to match one another.
Remove back cover of the opener remote.
Flip opener remote over. Use small screwdriver to move switches
to random positions. If you have more than one transmitter, now
is a good time to set them all with the same code.
1
1 2 3 4 5 6 7 8 9
2
All Mighty Mule transmitters are set to a standard code at the factory. However, for your safety and security, we
strongly recommend
that you replace the factory setting with your own personal code. Follow the directions below:
