1
PD300Z-2 PLUG-IN LAMP MODULE
The GoControl™ family of Z-Wave® certifi ed wireless lighting products
(smart LED fi xtures, bulbs, switches, dimmers, outlets, plug-in modules, and
thermostats) and security devices (alert sounder, motion sensor, and door/
window sensor) bring a new level of intelligent wireless capability to commercial
and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices from
other manufacturers and/or other applications. All non-battery operated nodes
within the network will act as repeaters regardless of vendor to increase
reliability of the network.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
This product supports 40Kbps data transmission.
This product can also
be used for network support in systems that stream metadata. An example
might include transmission of information from audio devices such as song
title, artist, and album information to various displays around the home. As part
of a Z-Wave network, the PD300Z-2 will act as a wireless repeater to insure
that commands intended for another device in the network are received. This
is useful when the device would otherwise be out of the radio range of the
wireless controller.
For indoor use only. Retain instructions for future use.
INSTALLATION
Plug this Lamp Module into the wall outlet near the lamp to be controlled, and
plug the lamp into the Lamp Module. Make sure the lamp(s) to be controlled
total no more than 300 watts.
To reduce the risk of electric shock, this product has a grounded type plug that
has a third (grounding) pin. This plug will only fi t into a grounding type power
outlet. If the plug does not fi t into the outlet, contact a qualifi ed electrician to
install the proper outlet. Do not change the plug in any way.
WARNING:
Plugging a non-resistive load such as fl orescent lighting or a device
with a motor may result in damage to the Lamp Module and will void the warranty.
✓
NOTE: The grounded outlet on the right side of the module is always
powered and can be used for any other appliance.
Adding to a network:
See the Wireless Controller operating instructions for details to include this
module under the command of the Wireless Controller.
1.
Prepare the Controller to include a unit to the network, by adding it to a
group (method of adding a node to the network). Refer to the Controller
instructions.
2.
The PD300Z-2 must be in its permanently installed location.
• For NWI Inclusion, press the button on the PD300Z-2 once.
• For classic inclusion, press the button on the PD300Z-2 twice.
3.
You should see an indication on your Controller that the “DEVICE WAS
INCLUDED” in the network.
✓
NOTE:
If you have trouble adding the PD300Z-2 to a group it may be that
the Home ID and Node ID were not cleared from it after testing. You must
fi rst “RESET UNIT” with your controller to remove it from the network.
Although adding it to a group includes it in the network, removing it from
a group does not remove it from the network. If removed from a group, it
functions only as a repeater.
Removing from a network:
The PD300Z-2 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1.
Set the Controller into Removal Mode and follow its instruction to delete the
PD300Z-2 from the Controller.
2.
Remove the switch by press the button twice.
3.
You should see an indication on your Controller that the “device was
removed” from the network.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,PD300Z-2,GO CONTROL; P/N: 10008878 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
PD300Z-2
Z-Wave Radio Frequency (RF) Controlled 300 Watt, 120 VAC
NWI and Scene Capable, Plug-In Lamp Module, Series 300
NOTE:
This unit must be added to the Network
only where it will be permanently installed.
The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.
120 VAC
CONTROLLED
OUTLET
120 VAC
ALWAYS ON
OUTLET
OPERATE / PROGRAM
BUTTON
Button Functions
1.
Use to include module under the
command of a Controller.
2.
Local ON and OFF control of the
connected load (push and release).
3.
Local dimming (hold down).
