Nortec EL005 Installation Manual Download

Page: 13 / 78

Product Overview

Nortec EL

2582302_C_EN_1611

Figure 3:

Circuit Protection

MADE IN CANADA

HUMIDIFIER

LISTED

205X

MODEL:

VOLTS:

AMPS:

KW:

MAX:

XXXXXXXXXXXXXXXXXXXXXXXX

S/N:

XXXXXXX

XXXXXXXXXXXX

PHASE:

XXXX

HZ:

XXXXXX

XXXXX

XXXXXXXXX
XXX

DATE:

XXXXXXXXX

XXXXXXXX B

AMPS

Nortec EL Steam Humidifier Specification Label

4.4

Options

Table 2

shows the list of options for the Nortec EL steam humidifier. Contact your Nortec representative

for details.

Table 2: Nortec EL Options

Option

Application

Mounting bar

Provides two mounting bars which fit into each other for wall mounting. One bar is fastened

to the humidifier, the other bar is fastened to the wall. The unit can be hung onto the wall by

engaging the two mounting bars.

Note:

The unit can also be wall mounted (without this op

tion) using the keyhole cutouts on the back of the humidifier housing.

Mounting rack

Stand-alone rack for mounting the Nortec EL steam humidifier.

Remote fault indication PCB

(printed circuit board)

Printed circuit board with relay contacts for connecting remote status displays for “Unit On”,

“Steam”, “Error” and “Service”.

Accessory relay PCB

(printed circuit board)

Printed circuit board with relay contacts for connecting other accessories such as fans and

supply water flushing valves.

Internal primary fusing

Optional internal fuse for heating voltage power supply. Only available as a factory-installed

option.

Note:

This is not a substitute for a dedicated external disconnect switch.

Fill cup extension

Kit for extending the fill cup so the humidifier can accommodate backpressure of up to

10 in H20 (2.49 kPa).

Extreme drain water cooling

Kit for cooling drain water to less than 120°F (49°C) before it is discharged into the drain.

Foam detection kit

Kit for extending the ability of the humidifier to handle a wider range of water supply quality.

BACnet MSTP BTL

PCB to provide BTL certified BACnet MSTP. This option also enables full Master functionality

when using BACnet MSTP.

BACnet IP BTL

PCB to provide BTL certified BACnet IP.

LonWorks board

Supplementary board to connect the Nortec EL to a building management system using

LonWorks.

Summary of Contents for EL005















































































Search results

Summary of Contents for EL005

Reviews:

Related manuals for EL005

Brands by name

Popular brands

Nortec EL005, Installation Manual

Search results

Summary of Contents for EL005

Reviews:

Related manuals for EL005

Brands by name

Popular brands