background image

WARRANTY:

 Under normal use the Company warrants 

to the purchaser that defects in material or workmanship 
will be repaired or replaced without charge for a period 
of 18 months from date of shipment, or 12 months from 

the start date of operation, whichever expires fi rst. Any 
claim for warranty must be reported to the sales offi ce 

where the product was purchased for authorized repair or 
replacement within the terms of this warranty. 

Subject to State or Provincial law to the contrary, the 

Company will not be responsible for any expense for 
installation, removal from service, transportation, or 
damages of any type whatsoever, including damages 
arising from lack of use, business interruptions, or 
incidental or consequential damages.

The Company cannot anticipate or control the conditions 
of product usage and therefore accepts no responsibility 
for the safe application and suitability of its products when 
used alone or in combination with other products. Tests 
for the safe application and suitability of the products are 
the sole responsibility of the user.

This warranty will be void if, in the judgment of the 
Company, the damage, failure or defect is the result of:

• 

Vibration, radiation, erosion, corrosion, process 
contamination, abnormal process conditions, 
temperature and pressures, unusual surges or pulsation, 
fouling, ordinary wear and tear, lack of maintenance, 
incorrectly applied utilities such as voltage, air, gas, water, 
and others or any combination of the aforementioned 

causes not specifi cally allowed for in the design 

conditions or,  

• 

Any act or omission by the Purchaser, its agents, 

servants or independent contractors which for greater 
certainty, but not so as to limit the generality of the 
foregoing, includes physical, chemical or mechanical 
abuse, accident, improper installation of the product, 
improper storage and handling of the product, improper 
application or the misalignment of parts.

No warranty applies to paint fi nishes except for manufacturing 

defects apparent within 30 days from the date of installation.

The Company neither assumes nor authorizes any person to 
assume for it any other obligation or liability in connection 

with the product(s).

The Purchaser agrees that all warranty work required after 

the initial commissioning of the product will be provided 

only if the Company has been paid by the Purchaser in full 

accordance with the terms and conditions of the contract.

The Purchaser agrees that the Company makes no warranty 
or guarantee, express, implied or statutory, (including any 
warranty of merchantability or warranty of fi tness for a 
particular purpose) written or oral, of the Article or incidental 

labour, except as is expressed or contained in the agreement 
herein.

LIABILITY: 

Technical data contained in the catalog or 

on the website is subject to change without notice. The 
Company reserves the right to make dimensional and other 

design changes as required. The Purchaser acknowledges 

the Company shall not be obligated to modify those articles 
manufactured before the formulation of the changes in 
design or improvements of the products by the Company.

The Company shall not be liable to compensate or indemnify 

the Purchaser, end user or any other party against any actions, 

claims, liabilities, injury, loss, loss of use, loss of business, 
damages, indirect or consequential damages, demands, 

penalties, fi nes, expenses (including legal expenses), costs, 

obligations and causes of action of any kind arising wholly or 
partly from negligence or omission of the user or the misuse, 
incorrect application, unsafe application, incorrect storage 
and handling, incorrect installation, lack of maintenance, 
improper maintenance or improper operation of products 
furnished by the Company.

Oakville

1-800-410-3131
1-905-829-4422
F 905-829-4430

Orillia

1-877-325-3473
1-705-325-3473
F 705-325-2106

Edmonton

1-780-466-3178
F 780-468-5904

5918 Roper Road
Alberta, Canada T6B 3E1

Houston

1-800-654-2583
1-713-433-2600
F 713-433-4541

Denver

1-855-244-3128
1-303-979-7339
F 303-979-7350

For further assistance, please call 24hr hotline: 1.800.661.8529  (U.S.A. and Canada)
Please have model and serial numbers available before calling.

PLEASE ADHERE TO INSTRUCTIONS IN THIS MANUAL

Failure to do so may be dangerous and may void certain 
provisions of your warranty.

Summary of Contents for XGB Series

























Reviews: