Norsat ATOM Ku GaN 20W Operator'S Manual Download Page 14 | Manualshive

Page: 14 / 42

background image

© Norsat International Inc.

(“Norsat”) All Rights Reserved

2021-09-02 052910 Rev E

14

2.5 Performing firmware update

Performing firmware update using

Kermit

client by

Ethernet interface

is recommended for firmware versions

2.0.0 or later. For firmware versions older than 2.0.0, use

serial port connection

with

ATOMControl

software.

ATOMControl

is a program designed for monitoring and controlling Norsat’s ATOM Series of BUCs and

SSPAs. This software and user manual are available on the Norsat ATOM Series website.

Caution: Always back up the settings of the BUC or SSPA before updating firmware using the latest
version of ATOMControl software. Refer to ATOMControl User Manual for how to back up and restore
device settings to and from an ATOM configuration file.

Firmware Update Using Kermit Client by Ethernet

Firmware version 2.0.0 and later running on the BUC or SSPA support firmware update by

Ethernet

interface using

Kermit

client software.

Tera Term

and

HyperTerminal

are recommended as clients for

updating firmware on the BUC or SSPA.

The following illustrates how to configure

Tera Term

for firmware image upload. Configuring and operating

other Kermit clients are similar.

Figure 2-5: Tera Term Client for Firmware Image Upload

«
...
12
13
14
15
16
...
»

Summary of Contents for ATOM Ku GaN 20W











































Reviews:

No comments

Related manuals for ATOM Ku GaN 20W

Brand: Redgum Pages: 12

Brand: Schumacher Pages: 45

Brand: Tripp Lite Pages: 4

Brand: Allen-Bradley Pages: 4

Brand: APS Pages: 70

Brand: National Instruments Pages: 4

Brand: SunSynk Pages: 10

VECTOPOWER VP600 Series

Brand: Aradex Pages: 114

Brand: R3Di Pages: 10

Brand: Tektronix Pages: 41

ColourTran-350 CTR-30-025-T-DD

Brand: Mode Lighting Pages: 2

Brand: Midian Electronics Pages: 4

Brand: Lindy Pages: 12

Brand: ZIMO Pages: 79

Brand: Ocean Matrix Pages: 4

Brand: Velleman Pages: 33

Brand: Unicont SPb Pages: 21

B-HDMI-ASI-IP-4CH

Brand: Questtel Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands