14
EN
BMK720W
5. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.
Impact drill safety warnings
▪
Wear ear protectors with impact drills.
Ex-
posure to noise can cause hearing loss.
▪
Use the auxiliary handle supplied with the ma-
chine.
Loss of control can cause personal injury.
▪
During operation provide eye protection
to prevent eyes from exposure to flying
particles.
Wear goggles.
▪
Take protective measures against inhala-
tion of dust. Some materials can contain
toxic ingredients.
Wear a dust mask and
work with dust/chip extraction when connect-
able.
▪
Hold the power tool by insulated gripping sur-
faces only, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord.
Cutting accessory contacting a “live”
wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
▪
Do not process materials containing asbestos. Asbes-
tos is considered carcinogenic.
WARNING:
Before connecting a tool to a
power source be sure that the voltage supply is the
same as that specified on the nameplate of the tool.
▪
A power source with a voltage greater than that speci-
fied for the tool can result in serious injury to the user,
as well as damage to the tool.
▪
If in doubt, do not plug in the tool.
▪
Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
▪
Fully unwind cable drum extensions to avoid potential
overheating.
▪
When an extension cable is required, you must en-
sure that it has the right ampere rating for your power
tool and it is in safe electrical condition.
WARNING:
Always switch off and un-plug the
power tool prior to any adjustment, servicing or main
-
tenance.
▪
While operating the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more securely with both hands.
▪
Prior to operation use suitable detectors to determine
if utility lines are hidden in the work area or call the lo-
cal utility company for assistance. Contact with elec
-
tric lines can lead to fire and electric shock. Damaging
a gas line can lead to explosion. Penetrating a water
line causes property damage or may cause electric
shock.
▪
Always keep the cord away from the working area of
the power tool.
▪
Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains plug
when the cable is damaged while operating. Dam-
aged cables increase the risk of electric shock.
▪
Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
▪
Use clamps or a vice to secure your work whenever
possible.
▪
Watch out for the initial torque reaction of the machine
or upon jamming the drill bit. Switch the power tool
immediately upon jamming the drill bit. Watch out for
high reactive torque which may result in kick-back.
The drill bit will block if the power tool is overloaded or
if the bit jams into the material.
▪
Do not touch the drill bit or parts close to it during op-
eration and immediately after that; they may be ex-
tremely hot. You may get serious burns.
▪ Keep work area clean. Blends of materials are par
-
ticularly dangerous. Dust from light alloys can burn or
explode.
▪
Rags, cloths, cord, string and the like should never be
left around the work area.
▪
Always switch the machine off prior to leaving it down.
▪
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its po-
tential hazards. Children and frail people must not use
this tool. Children should be supervised at all times if
they are in the area in which the tool is being used. It
is also imperative that you observe the accident pre-
vention regulations in force in your area. The same
applies for general rules of occupational health and
safety.
▪
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪
The power tools must not be used outdoors in rainy
weather, or in moist environment (after rain) or in close
vicinity with easily flammable liquids and gases. The
working place should be well lit.
Know your product
Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Securing screw
2. Chuck
3. Place for fixing the spindle
4. Drill journal
5. Operation mode selector switch
6. Ventilation slots
